Skip to main content

WLAN AND INTERNET STRUGGLE

This LENOVO X60  W10 upgrade   W10

W10 is working surprisingly well on this older laptop.
it seems less slow and all installed programs working  fine after the upgrade.

 2 problems solved  meanwhile
The Lenovo X60 did wake-up with WLAN adapter working  after unchecking power save on that device
And the 2nd WLAN router Eminent outside works after plugging the cable in the W-LAN port.
it was always?  in 1 of the LAN ports  i thought


But it has an issue with waking up the WLAN adapter
after wakeup it connects to WLAN but "no internet"

network diagnosis say  can not determen the problem
the
Intel(R) PRO/Wireless 3945ABG Network Connection
adapter reports this device is working well.

I know  I have to reboot the system to get the WLAN working again

annoying
 one way to trick this out is to select device  properties  and then change one of the many properties
just one  of them  remember the change. I changed the WMM Enabled setting
say okay and watch the WLAN icon right under corner of the screen it should turn red and come back again normal.
The adapter was reset without reboot  hurray!
There are many options but the most important the RESET is absent.
Now I have unchecked the power saving option of this WLAN adapter will see.
Why this simple reset is always missing in the PC WLAN devices?
a RESET function is one of the most important functions in the WLAN world
Some WLAN devices are very unstable, the time between failing  is short
some  WLAN devices need resets every few hours  other can work a few days..


Comments

aartw said…
Jaap hier hetzelfde probleem hoewel ik de PC niet laat slapen
http://www.geekbuying.com/item/Wintel-Keyboard-MINI-PC-Windows-10-Intel-Z3735F-2G-32G-802-11-b-g-n-LAN-Bluetooth4-0-HDMI-VGA-362181.html

ps geweldig ding.

Mijn oplossing.
De-activeer netwerk
Activeer netwerk.

Aart

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het