Skip to main content

shack empty still WSPR on


After more then 20 years my radio room had to be complete cleared out for a new floor.
What a lot of things gathered together in all these years.
It is a travel back in time this cleaning up operation.
It took many days to remove 3 tables 2 bureaus and all other furniture and radio stuff Including even my LP record collection.

 Good that my cat is helping me where she can.

The room sounds empty the acoustic is better. Now only 1 shelf on the wall with the K3 is left And still running WSPR 10m is very good today heard KH7Y lp 28400 loud with EU pile. first time this season a 80m west-coast decode and again the best possible DX on 28MHz 2013-11-28 08:24 ZL2IT 28.126084 -23 0 RF80km 5 PA0O JO33hg 18312 337 2013-11-28 07:46 W1CK 3.594049 -12 0 DM13ie 5 PA0O JO33hg 8987 30

Comments

VE9KK said…
Jaap at least it gives you a great chance to clean up and set the station up in a different way when all things come back together.
Mike

Popular posts from this blog

SPF5189z Low noise preamp 23cm

14-4-2018 updated


Above the low noise  preamp 50 - 4GHz    ebay  6€

Tested  2 small porto antennas
1 Baofeng UV antenna left   2nd best signal on PI2NOS
2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected
3 piece of wire :   best signal in the setup...

Unit under test at workbench.
It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA
And i could  no longer adjust it with the negative bias Voltage.
The - Voltage went to zero and the SPF input port became low Z.
This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench.

The specs of  SPF5189z  say it has an internal circuit  regulating the bias current.
Replaced . again   with an other of the 5 spare SPF i have.
The new one again could be adjusted at 50mA  5V 
The current raises to 150mA  when removing the  negative gate voltage.
Where is that internal bias circuit ?
I suspect  eBay …

2011-01-22 DIAMOND X30 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this Diamond collinear 70/2 combi antenna at a height of 25m. I needed to investigate what could be wrong.
Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E
The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size but it is no longer selling i think. This H43
3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire.
With this dipole the signals where totally worse. So the Diamond does work?
I got curious to look inside. Maybe moisture penetration degraded the antenna.
This  antenna is rainwater close in its normal vertical mounting position. But take care if your mast can b…

Nice opening10m and 12m to S.A.

SFI  low 70 a 16 K3  still 10m opened up in afternoon to N-Italy EA5 F JN33
F/PD0OHW/M in JN33 decoded 150mW

VP8LP  12m    2-way with GP 7m ag swr 1:3


60m 5,362 open to ZL every? morning