Skip to main content

PACC contest 2026

 Was weer een heel evenement veel pileups.

Helaas besloot mijn Steppir niet mee te werken en kon niet worden gebruikt dat was een behoorlijke aderlating natuurlijk dat deze beam uitgerekend tijdens de PACC niet werkte.

 Onder voorbehoud preliminary result PACC low (100W) CW

SINGLE-OP ALL LOW CW
--------------------
  1.          PA4O     432900   Electronic Log
  2.          PA0O     325728   Electronic Log
  3.        PA3GPX     187510   Electronic Log
  4.        PA3ARM     186200   Electronic Log
  5.         PA4PA     166374   Electronic Log
  6.          PA8R     118872   Electronic Log
  7.          PA2W     117279   Electronic Log
  8.         PA8MM     110976   Electronic Log
  9.         PA7RA      97838   Electronic Log
 10.          PE4A      85000   Electronic Log 

Logged around 1400 QSOs. My SteppIR 3‑el froze solid at –8°C during the night, so that was the end of that. Had to fall back on the old multiband dipole, part of a lightweight Hidaka Denki Works 4‑el yagi.

As usual, the rate collapsed around 02:00 local, even though the RBN still showed the bands open. Took a break until 06:00 no way I’m catching Peter PA4O, he always digs up more QSOs, 200 more! somehow. Ran the trusty K3, the CW beast, with the dipole on 10/15/20/40, Windom on 80/40, and a 25‑m high inverted‑L for 160.

Had the Flex 6500 in SO2R with the SO2Rduino (K1XM), but honestly it didn’t help much. Band switching in N1MM with Page Up/Down is quick enough. It was an SO2R experiment anyway. Might have helped Sunday morning with the 3‑el to the east on 10 or 15, but with the SteppIR frozen stiff that plan died fast.

 

 



Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

WSJT-x multiple instance

I am testing with 2 instances  WSJT-x  latest version. Using N3IZN notes on gougle.groups.com/forum/#topic/2-meter-wspr/oONMxyALMTO This is simple using  2 shortcuts to WSJT-X   with  command line  option --rig-name=xxxx This command line option creates separate program environments with different configurations. 2 (or more)  rigs can be used simultane with WSJT-x  at the same PC A second instance of WSJT-x  for the 2nd Rig  and the logging is needed \ The shortcuts to WSJT-x  have to be modified to accomplish this. to add a second separate working instance for WSJT-x make a copy of the first shortcut to WSJT-x rename the shortcut to rig2       rig2  is the name you want to use for your rig r-click on this WSJT-x rig2 open properties change the target name to C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=rig2 ( 1 space between wsjtx.exe. and --rig-name=rig2    and rig-namem m...