Skip to main content

Verassing 6m was eigenlijk al een paar dagen "dicht" duikt ineens 7O/DL7ZM op eerst FT8 later CW

7O/DL7ZM – Yemen | DX-World

 

7O/DL7ZM – Yemen | DX-World

David  gaf aan:  CW  vond hem heel zwak op 50.095 de oude stoffige CW frequentie heel zwak amper s3 maar  reageerde direct nét voor de meute aan de eerste tuners en out of pace tx'rs waren er al. 

Rare gewoonte tunen óp de DX frequentie dat doen velen.. ja een 2x GS35 PA moet getuned :-)

Daar ook met blote "100W"  ging een stuk vlotter dan metFT8 tussen de big guns... IC7100 ca 90W 7ele moest snel keyer om pluggen  de IC7100 had geen data output door onverwachte fout in configuratie vandaar kon het ook niet kon lukken met FT8 mazzel dus dat David een CW man is..

Nieuw DXCC  #216  wwloc LK62VP?  met CW! wie verwacht zoiets


Labels:

Comments

PE4BAS, Bas said…
Gefeliciteerd met de nieuwe DXCC op 6m. Het lukt je nog steeds ;-). Helaas gemist hier, mij te warm om in de shack te zitten. En andere bezigheden met dit warme weer. 73, Bas
June 24, 2022 at 8:06 AM
pa0o said…
idd gisteren was het erg warm maar we houden het koel in huis
Ik had hier ook wel weer wat klussen
vandaag 6m FT8 kort 2 JA gezien 9M4BCN gewerkt YB5QZ langdurig CQ tot -9 hier maar hij zag me niet zelfs niet met HP 800W..
dan is een echt CW QSO tussen 2 low power station wel even meer waard
June 24, 2022 at 9:25 PM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
12 comments
Read more

WSJT-x multiple instance

I am testing with 2 instances  WSJT-x  latest version. Using N3IZN notes on gougle.groups.com/forum/#topic/2-meter-wspr/oONMxyALMTO This is simple using  2 shortcuts to WSJT-X   with  command line  option --rig-name=xxxx This command line option creates separate program environments with different configurations. 2 (or more)  rigs can be used simultane with WSJT-x  at the same PC A second instance of WSJT-x  for the 2nd Rig  and the logging is needed \ The shortcuts to WSJT-x  have to be modified to accomplish this. to add a second separate working instance for WSJT-x make a copy of the first shortcut to WSJT-x rename the shortcut to rig2       rig2  is the name you want to use for your rig r-click on this WSJT-x rig2 open properties change the target name to C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=rig2 ( 1 space between wsjtx.exe. and --rig-name=rig2    and rig-namem m...
Post a Comment
Read more