Skip to main content

Windows10 experience


 I did install the technical preview of Windows10  on a separate HD
After some puzzling how to make an boot-able external HD
A process that is complicated in Windows.
 I had my old W7 HD  backup since replacing it for a SAMSUNG SSD 500G EVO
SAMSUNG has its migration tool to move a complete HD  to the SSD ( SAMSUNG SSD only)
From a running W7 system without any problem.
No need for disk image boot CD.
What I was looking for was a simple way to repair my W7 HD where Windows was deleted
Just copying back the Windows map is way too simple...
Just because some parts are missing the drive had to be reformatted destroying installed software Throwing through the window all the time spend on installing those parts.
Making a bootable usb / HD W10  a lot of discussion can be googled  about this subject.
more methods can be used but a very simple method does not exist.
Easy BCD 2.2 of Neosmart supposed be able to do this easy but I could not find out how to make sure what drive I was making boot-able confusing and to risky to work with.
Why is it still needed to follow the relative complicated way
with the power-full dos commands also risky.
diskpart
list disk
select disk x (X is de driveletter die overeenkomt met de USB HDD)
clean
create partition primary
active
format fs=ntfs qucik
assign
exitk

Mount de Windows 7 of 8 ISO Image in een Virtual Drive. Dit kan met de freeware applicatie MagicDisc
De USB Drive Bootable maken.
Ervan uitgaande dat H:  de virtuele drive letter is waar het ISO-image van Windows 7 of 8 is geplaatst en G: gekoppeld is aan de Externe HDD.
Open de command prompt en voer de onderstaande commando's uit.

h:
cd boot
bootsect.exe /nt60 g:
Why SAMSUNG migration can do this automatic?
anyway i had to reformat my old HD since it did not want to boot W7 anymore.
An upgrade W7 to W10 could be available short time.

I moved W10 to the HD and installed it
The HD was bootable when placed in the SATA slot of the LAPTOP
But it did not boot as USB device.
The W10 logo came on and the waiting circle but nothing more.
The disk activity LED stopped blinking and went to stable on.

But with the drive intern I could run W10
Installed VB6SP6   using a special installer for that.
VB6 IDE did run but the data environment msde.dll did not install no reason given.
Could not do a complete test without connection to a database.
Then last evening W10 did an update and after that i could not start
it needs repair  but no repair path was given.. it stays in an endless startup loop
My W10 experience was ended after last night.
But tt looked okay W10 the start button was back and VB6 could run the IDE more the in W8

Tried to install the W10 32bit version
but got struck with this message

 a hopeful start...
but then after 10 seconds



Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more