Skip to main content

TX6G Australis

Vanavond redelijk gehoord op 28020 CW
 helaas geen tijd na een paar pogingen moest ik stoppen.

Deze TX6G  expeditie  heeft zeker oor voor W-Europa ( met name G)   met Nigel G3TXF  erbij dat zit wel goed.
Inmiddels  LOTW cfm  op  15 cw en 10 phone ook gelukt ondanks de tremendous EU pile
Het regent elke dag op Australis hoorde ik dat verwacht je niet zo op 20graden zuiderbreedte in Polynesie.

DetailsPA0OTX6G2014-03-22 14:31:1715MCW21.02213AUSTRAL ISLAND
DetailsPA0OTX6G2014-03-22 13:07:5912MCW24.89691AUSTRAL ISLAND


Vandaag geprobeerd  de multi band dipole  op 12 17 en 30m te brengen.  12m werkte wel aardig  17 minder TX6G was op 17m zwak  op 10m waren ze 56 phone.
Met  de sterke wind is het erg lastig draad antennes niet in de knoop te krijgen of vast in de bomen.
Dat werd laatst in DWDD uitgelegd  de chaos theorie verklaart het verschijnsel dat snoeren een voorkeur lijken te hebben om in de knoop te raken. Nou dat kon ik vandaag heel goed waarnemen.  

Heel anders dan die Italia  only  expeditie's  Zoals Zambia 9J2T. Vanaf het 1e moment dat ik ze bezig hoorde op 40m duidelijk dat het verder tijd verknoeien was om verbindingen te maken als niet Italiaan.

2 Meter storing gevonden  zat toch gewoon in de keuken een Ledlamp zat te storen op VHF 135 - 146 MHz.  Dat kon ik niet vinden met de RF snuffelaar "Tapir"  van Elektor die is wel zeer gevoelig maar dit type storingen op VHF  met relatief lage energie vind hij niet.

de boosdoener  een ouder type ledlamp dat kan dus ook nog.


Vervangen door een IKEA LED lamp 400lumen  de storing op 144 was weg
Toch weer gewoon in huis..  Heb nog rondgefietst met de rf detector  je hoort alle straatlantarens de sportveld verlichting etc   maar deze specifieke frequenties vind je alleen met een ontvanger en richtantenne. Of gewoon door afschakelen van mogelijke stoorbronnen.

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...