Skip to main content

ARRL CW

Het ging de laatste tijd alleen maar berg af met de propagatie.
Veel  geomagnetisch stormen.
Dan was 10m toch nog redelijk open zaterdag middag.


160m was de slechtste band
aantal gehoorde stations slechts 5 
Met 100W was er niet veel te beginnen
Maar toch KC1XX en KM1W  beiden op 6 banden 
 W3LPL  kon me niet horen  eindeloos CQ hoorde niemand!
Jammer dat zou ook een 6-bander zijn.


Op 80m ging het s'morgens goed.    Wat ik hoorde kon ik gemakkelijk werken.  Ik hoorde velen tevergeefs roepen
 Dus slecht kan de   geïmproviseerde  80  "shunt" verticaal niet zijn.
40m zondag ochtend  goed open naar west-kust   NV MT UT BC WA CA   ze kwamen allemaal tot verbazing retour.

Ook de  duoband 30/40 inv-V dipool  kan nooit helemaal trash zijn ik kwam in de piles redelijk snel aan de beurt.

de teller staat  10uur lokaal op 369Q  141 multy's


live score te volgen op
http://www.getscores.org/live/


Zondag  10m  zwak  geen nieuwe stations kunnen werken
Maar  15m was tijdens SS  super veel multy  NV UT WA CA BC    SK nog gehoord 
Dat maakt de ARRL weer mooi. Ik werd een beetje verzadigd van al die oostkust W's  


op 160m zondag tegen einde  alleen VE1ZZ  599! 
Op 80 en 40 nog wat multies erbij


0.0  Wyoming en Southdakota!
de eindscore







QRV 4M   transverter (old 6m)  + BLF177 
7ele 2/4/6m 3-band  met 160m inv-L white wire feed through using isolated stand-off  




Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
12 comments
Read more

WSJT-x multiple instance

I am testing with 2 instances  WSJT-x  latest version. Using N3IZN notes on gougle.groups.com/forum/#topic/2-meter-wspr/oONMxyALMTO This is simple using  2 shortcuts to WSJT-X   with  command line  option --rig-name=xxxx This command line option creates separate program environments with different configurations. 2 (or more)  rigs can be used simultane with WSJT-x  at the same PC A second instance of WSJT-x  for the 2nd Rig  and the logging is needed \ The shortcuts to WSJT-x  have to be modified to accomplish this. to add a second separate working instance for WSJT-x make a copy of the first shortcut to WSJT-x rename the shortcut to rig2       rig2  is the name you want to use for your rig r-click on this WSJT-x rig2 open properties change the target name to C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=rig2 ( 1 space between wsjtx.exe. and --rig-name=rig2    and rig-namem m...
Post a Comment
Read more