Skip to main content

SGC-230 TUNER damage

Inside watertight box of the SGC-230 near the power terminals exploded fuse and some damage is visible besides that no damage to the PCB
 
 This SGC-230 tuner is damaged after applying 230AC at the 14VDC connection
.wasn't  me !
 
First investigation showed CPU and most IC's damaged 
 at least those connected to the 14VDC power 
 
A simple 50cent  suppressor diode could have prevented this to happen,
 but no protection was cheaper..

The 5V regulator and the 3 relay driver IC's destroyed ad others  by the high voltage flash .
the relays are tested okay not that many chips involved but the most essential CPU is hard to get.
The SGC factory seems no longer to exist.
Looks like a total loss ...only  chance to save her
With a  programmed CPU or  the V1.03 firmware ?
 possible an ex employee of SGC.The firmware resites in a PC somewhere ?

The  CPU is  MC68HC711E9    I think she is still offered on Ebay

 I hope to replace the controller with an Arduino and K3NG based software

The logic IC's are not expensive  anyway I am trying to salvage this tuner.



the 3 driver chips,UA7805,TC7660(-5V )   removed







Labels:

Comments

PE4BAS, Bas said…
230V er op gezet omdat er 230 opstaat natuurlijk, ja ik snap het. Toch zou ik op mijn CG3000 nooit 3000V zetten ;-). 73, Bas
October 20, 2023 at 12:47 PM
pa0o said…
Ja haha zou het misverstand ligt om de hoek
misschien is er nog iemand ergens die de software op zijn PC heeft staan
anders is het wel einde verhaal
of de source code van N7DDC ombouwen....
October 22, 2023 at 2:39 AM
pa0o said…
N7DDC heeft de source niet op github wel de f.w.
October 22, 2023 at 3:08 PM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more