Skip to main content

FB tropo first good tropo 2021 (hope in the contest weekend same ...;-) and "my" 23cm Beacons overview

The beacons i can hear / detect in JO33HG  in flat propagation at 1296MHz 

 OZ7IGY   1296.930 very weak copy  when not in PI mode..

DB0VC  xx.920 JO54if 100% in almost all conditions

DB0XY  x.912 JO51EU  100% one of the stronger

DB0GW  x.951  JO31jk  Munster always detected seems improved   specific frequency zig-zag below


  ON0VHF 100% 

PI6ASD x. 639 Amsterdam linear transponder 70cm in beacon mostly heard

PI7ALK  x.918  S5 normal back after few moths of  renovation fb!

GB3MHZ  x.830 100% copy 

DB0LTG   x.7435 100%

DB0MOT    detectable after some time..

PE9GHZ/B   1296.815 JO11MW  in/out 

 my 3cm  beacon at  10368.904 MHZ is still 24x7 on air pse spot it!





above my DF9IC 23cm PA build some time ago, i tested it but unfortunately no output 

I guess this project is the end of my home brew  attempts f.t.t.b... 

 Tonight Monday very good tropo  Beacons heard: SR1KOL  SR3HLY JO82LJ DB0UB JO62KK

LA1UHG LB2SHF SKMHI SK6UHI OK0EKL 

DX worked:

 SP4MPB KO01  CW    SP5XMU  KO02 965km  


205030 -18 -1.0 1567 ~ CQ SP7EXY KO00  SP  heard 1000km +

201930 -22 0.1 1184 ~ PA0BAT SP5BIN KO02 heard max -19

2021-02-28 22:32OZ4VV1296174.91FT8+13-05OZ
2021-03-01 10:14SP4MPB1296200.00CW599539SPKO01
2021-03-01 10:36DF5VAE1296174.91FT8+03+07DL
2021-03-01 14:49PH0TV1296174.91FT8-06-05PA
2021-03-01 19:24SP5XMU1296174.91FT8-6-12SPKO02
2021-03-01 19:33DG0FE1296174.91FT8-13-13DL
2021-03-01 19:38DG0DI1296174.91FT8+05+10DL
2021-03-01 19:40PA0BAT1296174.91FT8+00+00PA
2021-03-01 19:58SP1WSR1296174.91FT8+13+14SP
2021-03-01 20:03G4KUX1296174.91FT8-09-06G
2021-03-01 20:18DL5OCD1296174.91FT8-02-13DL

with old setup 35W rf at the feeder 1m2 disk SKY67151 LNA  DB6NT DF9NP 1150MHz tcxo 

XVTR is direct at dish , 

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het