Skip to main content

VHF DX ..

A92HK  70.154MHZ  cq +3  strong  FT8  ....but i can't work DX on 4m ???
With 100W 5ele  i was not heard dejavue, looks like 1k + is needed
Or move to DL where 15W erp is good enough to be the first one in the pile's..
2 years ago also A92GE i believe it was heard CQ good signal also no response
So 1x in 2 years can hear A92 at 4m once with a good signal just to tease me then the signal fades out never to be heard again. The only DX possible > 4000km   with Kazakhstan hams but they also have receiving problems.. I am o longer expecting to work DX  here


Since 29 may  an old 9ele Tonna  2m in top   23m above soil should be enough to have Es contacts elevated 5dgr
The antenna work was just finished when a huge ES opening  happened
7X2RO 7X2HF(hrd only)   9H1TX IT9    EA7 5 6  Italy  they where even workable in my location
of course i had to be  patient until no other callers to have a chance.
Much louder south of me as usual 
Very rare late night or early morning ES came back 144 ES at 01:30 local to CT and EA

The old but good 9ele Tonna  ( thanksTimon PA1T) it is a very light weight antenna modest gain but for ES she should be fine   unfortunately SWR went up after rain showers  this is an issue with the Tonna   I am thinking  to make it 2 band 2 and 70 to the concept of DK7ZB
I had  7 2m elements skeleton in the 4m 5ele antenne to have 2 bands 4 and 2m.
That 70MHz 144MHz does not go well together as skeleton duoband .  The 9 ele is a little improvement for 2m
I had expected more improvement against the 7 elements 5 ele 2m/4m combi the f/b ratio is now 20-30dB at it was only 10dB with  the duoband but it was not as bad as i thought .


Next
Call signWorkedDate/TimeBandModeFreqQSL
DetailsPA0OG1MHU2020-05-30 00:07:452MFT8144.17449
DetailsPA0OGM3NKG2020-05-30 00:05:302MFT8144.17449
DetailsPA0OM0HYE2020-05-30 00:04:002MFT8144.17449ENGLAND
DetailsPA0OCT7AGI2020-05-29 23:41:152MFT8144.17530PORTUGAL
DetailsPA0OCT1EOD2020-05-29 23:25:452MFT8144.17642
DetailsPA0OM0KBW/P2020-05-29 19:40:242MSSB144.25000
DetailsPA0OEB5HRX2020-05-29 17:37:522MSSB144.26584
DetailsPA0OEA5GX2020-05-29 17:32:512MSSB144.33463
DetailsPA0OEA5IDZ2020-05-29 17:18:002MFT8144.17646
DetailsPA0OEA3CBH/62020-05-29 16:40:402MSSB144.31463
DetailsPA0O7X2RO2020-05-29 16:36:342MSSB144.31968
DetailsPA0OEA6AAU2020-05-29 15:53:042MSSB144.29947
DetailsPA0OIZ7EWZ2020-05-29 15:49:382MSSB144.28954
DetailsPA0OIT9NDW2020-05-29 15:47:452MSSB144.35980
DetailsPA0OI0JX2020-05-29 15:46:302MSSB144.35972
DetailsPA0O9H1TX2020-05-29 15:45:512MSSB144.33970
DetailsPA0OIZ8FQO2020-05-29 15:43:532MSSB144.31981
DetailsPA0OIW0HLE2020-05-29 15:38:022MSSB144.28092
DetailsPA0OEA7BHO2020-05-29 15:21:452MFT8144.17484
DetailsPA0OEA7M2020-05-29 15:10:004MFT870.15502
DetailsPA0ODL2KV2020-05-29 15:09:004MFT870.15502FEDERAL REPUBLIC OF GERMANY
DetailsPA0OCT3HF2020-05-28 16:03:004MFT870.15525MADEIRA ISLANDS
DetailsPA0OPB2DJ2020-05-27 08:38:122MSSB144.31002
DetailsPA0ODJ6GI2020-05-26 20:43:0170CMFM431.45000
DetailsPA0OPA0LDZ2020-05-26 14:04:192MFT8144.17465
Next

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...