Skip to main content

28Mhz today




Next
 Call signWorkedDate/TimeBandModeFreqQSL
DetailsPA0OEA4HGR2020-05-16 10:38:0010MFT828.07512SPAIN
DetailsPA0OR9JAC2020-05-16 10:33:0010MFT828.07512 
DetailsPA0OR1AV2020-05-16 10:29:3010MFT828.07512EUROPEAN RUSSIA
DetailsPA0OBH4QYX2020-05-16 10:27:3010MFT828.07512CHINA
DetailsPA0OBG5EEF2020-05-16 10:21:0010MFT828.07512CHINA
DetailsPA0OEA5WP2020-05-16 10:17:0010MFT828.07512 
DetailsPA0OR1AP2020-05-16 10:15:0010MFT828.07512 
DetailsPA0OJH3QMF2020-05-16 10:12:0010MFT828.07641JAPAN
DetailsPA0OPA2DX2020-05-16 08:17:0010MFT828.07474 
DetailsPA0ORA1AMX2020-05-16 08:12:3010MFT828.07474 
DetailsPA0OR2AW2020-05-16 07:58:1510MFT828.07474 
DetailsPA0OOH7AWS2020-05-16 07:55:1510MFT828.07474FINLAND
DetailsPA0OUA9CQV2020-05-16 07:53:1510MFT828.07474 
DetailsPA0ORX9WN2020-05-16 07:52:1510MFT828.07474 
DetailsPA0ORA9J2020-05-16 07:46:4510MFT828.07474 
DetailsPA0OPA0AER2020-05-16 07:39:4510MFT828.07474 
DetailsPA0OR9HAK2020-05-16 07:38:4510MFT828.07474 
DetailsPA0ORA1AMX2020-05-16 07:36:1510MFT828.07474 
DetailsPA0OOG2A2020-05-16 07:31:4510MFT828.07515 
DetailsPA0OBD7BS2020-05-16 07:22:4510MFT828.07638CHINA
DetailsPA0OF5HNQ2020-05-06 08:44:4512MFT824.91573FRANCE
DetailsPA0OSP6EFY2020-05-06 08:36:3017MFT818.10073POLAND
DetailsPA0OSK0TM2020-05-06 08:34:3017MFT818.10073 
DetailsPA0ORC9YD2020-05-06 08:28:3017MFT818.10073 
DetailsPA0O4J75P2020-05-06 08:16:3017MFT818.10073 
Next

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more