Skip to main content

WSPR overnight result

TimestampCallMHzSNRDriftGridPwrReporterRGridkmaz# Spots
 2019-11-13 15:30  VK7DIK  3.570140  -21  0  QE38cu  5  PA0O  JO33hg  16733  308  10 
 2019-11-14 03:04  W4BCX  0.475671  -28  0  EL98pd  5  PA0O  JO33hg  7368  41  4 
 2019-11-14 02:08  WA1TCC  1.838099  -24  0  EM80il  5  PA0O  JO33hg  7335  41  8 
 2019-11-14 04:26  K4LY  0.475700  -19  0  EM85wb  5  PA0O  JO33hg  6882  43  1 
 2019-11-14 06:18  K9PAW  1.838190  -27  0  EN61ar  1  PA0O  JO33hg  6688  43  6 
 2019-11-14 03:36  K3MF  0.475797  -25  0  FM19sr  5  PA0O  JO33hg  6162  46  17 
 2019-11-14 00:26  W3SZ  0.475725  -30  0  FN20ag  5  PA0O  JO33hg  6089  47  3 
 2019-11-14 04:08  KB1MH  1.838080  -30  0  FN42ec  5  PA0O  JO33hg  5684  49  5 
 2019-11-14 03:16  AA1A  0.475675  -27  0  FN42pb  1  PA0O  JO33hg  5630  49  26 
 2019-11-14 06:18  W1IR  0.475744  -19  0  FN34lp  5  PA0O  JO33hg  5587  50  8 
 2019-11-13 19:52  EX0AA  3.570042  -19  0  MN72hu  2  PA0O  JO33hg  4984  308  15 
 2019-11-14 00:50  EB8ARZ/1  0.475793  -26  0  IL18uk  0.2  PA0O  JO33hg  3336  28  3 
 2019-11-13 15:44  PA0O  28.126009  -20  0  JO33hg  5  EA8BFK  IL38bo  3213  220  1 
 2019-11-13 18:36  EK1RR  3.570119  -22  1  LN20fe  0.01  PA0O  JO33hg  3180  310  3 

Comments

Jan / pa3abk said…
Jaap,
Good results on MF!
Comparing with other takers in EU.
Any secret on your antenna?
I did manage to get across the pound TX wise but didn't get that much RX spots.
Have cumbersome "noise" on this end.
And the horrible sigs of DL1HWK... Did you "null" him out?
Jan/pa3abk
pa0o said…
hallo Jan het moet de Beverage zijn ca 300m die doet het heel goed op 474.2
en DL1HWK veel IMD soms 4 of 6 sporen
op 80 en 160 is de Beverage niet veel beter dan de Vertikaal i-L 160 of dipool 80
ik gebruik de Flex1500 met een actief 630m band filter
band hopping 10 / 630m
P-SDR geeft geen signaal op 630m weer maar ontvangen doet de 1500 wel !

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het