Skip to main content

CQWW VHF


     ARRL Section : DX
        Club/Team : 19
         Software : N1MM Logger+ 1.0.7845.0

        Band   Mode  QSOs     Pts  Grd  Pt/Q
          50  CW      26      26   19   1.0
          50  USB     45      45   29   1.0
       Total  Both    71      71   48   1.0


EA8  was deze keer de ODX    niet de volledige tijd meegedaan not full time
NL: PA5WT  PA2REH  PA4EL heard

had to miss the Sunday evening 
ES to EA  I7/8 IS0(1) IT9  9H(1) ZB2(1) CT(3) EA8(2) CN8(1) SV OY LZ TA(2) 4X(2)
Some FT8 contest activity  but the  CQWW VHF site does not mention the use of FT8 contest mode?
And had a problem with FT8 contest mode the program crashed when logging
i upgraded to the latest WSJT-x  V2.1.0 but same crash 

sorry PA2REH trying to log you failed
I used only CW / USB mode then.

this run-time error popup came when pressing the log button, never had this before
after upgrading from V2.01 to the latest V2.1.0  i lost the CAT connection
the radio type  was set to the first entry of the list : ADAT  www.adat.ch ADT-200A
strange had to change it to K3





Comments

PE4BAS, Bas said…
Hallo Jaap, ik heb soortgelijke ervaring gehad in het verleden. Ik heb de CAT verbinding nu uitsluitend via HRD lopen en dat gaat tot nu toe altijd goed. Misschien de moeite waard ook eens naar JTDX te kijken, alhoewel ik vermoed dat je dezelfde foutmelding gaat krijgen.
July 22, 2019 at 12:46 PM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more