Skip to main content

latest LOTW contacts


Next
 Call signWorkedDate/TimeBandModeFreqQSL
DetailsPA0OJG0CQK2019-03-08 17:46:15160MFT81.90850JAPAN
DetailsPA0OT88XH2019-03-08 15:37:4540MFT87.07451 
DetailsPA0OEK3GM2019-03-08 10:24:1515MFT821.07472 
DetailsPA0OEA1YV2019-03-08 10:12:1515MFT821.07472 
DetailsPA0ONW9H2019-03-08 06:27:1560MFT85.35759UNITED STATES OF AMERICA
DetailsPA0OAH7C2019-03-08 06:03:4560MFT85.35759 
DetailsPA0OAH7C2019-03-08 06:03:3060MFT85.35700HAWAII
DetailsPA0OPU1SKS2019-03-07 16:57:4515MFT821.07473BRAZIL
DetailsPA0OPY2VA2019-03-07 16:40:1515MFT821.07473BRAZIL
DetailsPA0OBG9NJY2019-03-06 23:25:3060MFT85.35752CHINA
DetailsPA0OVU2OT2019-03-06 16:42:0060MFT85.35752INDIA
DetailsPA0OPY2EJ2019-03-02 11:59:3015MFT821.07461 
DetailsPA0O4Z5KU2019-03-02 09:33:3015MFT821.07483 
DetailsPA0OLU8HF2019-03-01 22:52:1560MFT85.35751ARGENTINA
DetailsPA0OPA7DA2019-03-01 14:56:304MFT870.15555 
DetailsPA0O4Z5UY2019-03-01 10:22:1515MFT821.07482ISRAEL
DetailsPA0OZS1XG2019-03-01 10:04:0015MFT821.07482REPUBLIC OF SOUTH AFRICA
DetailsPA0ORV6F2019-03-01 08:51:4515MFT821.07482 
DetailsPA0ORN6AJ2019-03-01 08:50:1515MFT821.07482EUROPEAN RUSSIA
DetailsPA0OZL4OL2019-02-28 08:06:3060MFT85.36279NEW ZEALAND
DetailsPA0OBD6JN2019-02-27 16:07:3060MFT85.35783CHINA
DetailsPA0OAH7C2019-02-26 18:44:4530MFT810.13832HAWAII
DetailsPA0OR6DP2019-02-26 10:32:3015MFT821.07465 
DetailsPA0OYD0EGA2019-02-26 10:30:0015MFT821.07465INDONESIA
DetailsPA0OVP9GE2019-02-26 07:43:4560MFT85.35766 
Next

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
12 comments
Read more

WSJT-x multiple instance

I am testing with 2 instances  WSJT-x  latest version. Using N3IZN notes on gougle.groups.com/forum/#topic/2-meter-wspr/oONMxyALMTO This is simple using  2 shortcuts to WSJT-X   with  command line  option --rig-name=xxxx This command line option creates separate program environments with different configurations. 2 (or more)  rigs can be used simultane with WSJT-x  at the same PC A second instance of WSJT-x  for the 2nd Rig  and the logging is needed \ The shortcuts to WSJT-x  have to be modified to accomplish this. to add a second separate working instance for WSJT-x make a copy of the first shortcut to WSJT-x rename the shortcut to rig2       rig2  is the name you want to use for your rig r-click on this WSJT-x rig2 open properties change the target name to C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=rig2 ( 1 space between wsjtx.exe. and --rig-name=rig2    and rig-namem m...
Post a Comment
Read more