Skip to main content

474.2

Monday after ARRLDXCW
-10dB strongest decode this season     -12 -14  a page full decodes FN42pb again
2017-02-20 01:38  WD2XSH/17  0.475647  -10  0  FN42pb  2  PA0O  JO33hg  5630  49 
it should be possible to have my signal decoded  i do not know the ERP of WD2XSH/17
there is 20dB power space with this signal levels
here about  60W rf   if it was 1 kW on the other site my snr about  -13  on the other site
But still no decodes



WD2XSH/17 best SNR  to -15dB  but again not outside FN main square
2017-02-18 01:08  WD2XSH/17  0.475647  -15  0  FN42pb  2  PA0O  JO33hg  5630  49
2017-02-18 00:52  WG2XKA  0.475721  -27  0  FN33lq  1  PA0O  JO33hg  5656  49 
 2017-02-17 23:46  WD2XSH/17  0.475647  -25  0  FN42pb  2  PA0O  JO33hg  5630  49 
 2017-02-18 02:54  WG2XPJ  0.475674  -28  0  FN34lp  1  PA0O  JO33hg  5587  50 
 2017-02-18 00:48  PA0O  0.475787  -29  0  JO33hg  0.2  RX3DHR  KO94ks  2095  72 
 2017-02-17 21:48  PA0O  0.475787  -26  0  JO33hg  0.2  EA7HPM  IM67xj  2017  214 
 2017-02-18 00:34  PA0O  0.475788  -27  0  JO33hg  0.2  EA5DOM-1  IM98xn  1713  200 
 2017-02-17 21:10  EA5DOM  0.475610  -24  0  IM98xn  1  PA0O  JO33hg  1713  15 
 2017-02-18 05:40  IO6KQM  0.475752  -26  0  JM48  0.002  PA0O  JO33hg  1654  355 
 2017-02-18 00:30  PA0O  0.475787  -26  0  JO33hg  0.2  OH6GAP  KP22rd  1482  41 
 2017-02-17 21:48  PA0O  0.475786  -12  0  JO33hg  0.2  OH2EAT  KP20xw  1437  46 
 2017-02-17 23:58  PA0O  0.475787  -25  0  JO33hg  0.2  EB3FRN  JN01mc  1416  199 
 2017-02-18 00:30  PA0O  0.475789  -27  0  JO33hg  0.2  EA3IW  JN11bj  1363  196 
 2017-02-18 00:42  PA0O  0.475786  -31  0  JO33hg  0.2  EA3AER  JN12kd  1268  194 
 2017-02-17 21:48  PA0O  0.475787  -3  0  JO33hg  0.2  LA2XPA/2  JP33wi  1124  3 
 2017-02-17 21:48  PA0O  0.475787  -26  0  JO33hg  0.2  SP5XSB  KO02ld  972  92 


2322  -24  -1.0    0.475625    0   LA1BCN        JO48     23    604

2322  -27  -0.3    0.475647    0   WD2XSH/17              37
only 2 Hz  higher and stronger  but WSPR decodes both !
2322   -7  -1.0    0.475649    0   LA3EQ         JO28     30    593

2322   -2  -0.5    0.475664    0   DJ0ABR        JN68     23    694

2322   -3  -0.8    0.475755    0   DH5RAE        JN68     27    694

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
12 comments
Read more

WSJT-x multiple instance

I am testing with 2 instances  WSJT-x  latest version. Using N3IZN notes on gougle.groups.com/forum/#topic/2-meter-wspr/oONMxyALMTO This is simple using  2 shortcuts to WSJT-X   with  command line  option --rig-name=xxxx This command line option creates separate program environments with different configurations. 2 (or more)  rigs can be used simultane with WSJT-x  at the same PC A second instance of WSJT-x  for the 2nd Rig  and the logging is needed \ The shortcuts to WSJT-x  have to be modified to accomplish this. to add a second separate working instance for WSJT-x make a copy of the first shortcut to WSJT-x rename the shortcut to rig2       rig2  is the name you want to use for your rig r-click on this WSJT-x rig2 open properties change the target name to C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=rig2 ( 1 space between wsjtx.exe. and --rig-name=rig2    and rig-namem m...
Post a Comment
Read more