Skip to main content

VB6 replacement search , TQSL small problem..

Perfectly describes the let down of VB6 users by Microsoft.

http://lightquick.co.uk/still-looking-for-a-replacement-for-vb6.html?Itemid=252

 i have installed MS Visual studio 2015   i had to let my PC running the whole evening to install this dragon piece ...

bulky slow cryptic not suited
Windows 10 still not been able to run in VM




seems to be very hard..
TQSL v2.0.3
I noticed  a possible problem in TQSL   v2.0.3

when editing an existing ADIF
the output is skipping fields

output of N1MM ADIF   1 record

 EA8AA/QRP 20150412 172233 36 20M PA0O 14.05356 DX 14.05356 CW 599 599 PA0O 33 8373 1 1 AF 1 1 True USER-PC 1


same record ADIF after edit   inTQSL

EA8AA/QRP
   20M
   CW
   20150412
   172233
   14.05356
   14.05356

 I noticed this because I could not import the edited ADIF into HAMlog due to too many missing fields

did send my findings to LOTW  / tqsl   
got real quick reply from Katherine Lotw specialist

 LOTW does only need  callsign  date time band mode and optional frequency
 therefore TQSL only exports these fields needed for LOTW

50MHz  3 days 3B9RF reported into Europe including SM6 LA EI north but for one or another reason i can not be present at the right time ....
frustrating to learn I am not a DX-r anymore .
A DX -r  just know when to be QRV  i know  it is dinnertime .. today I had! to have dinner somewhere outside..  I left with white noise  and returned  to find white noise
But in between 3B9RF was worked again PA LA  etc..
aaarggg I just can't be there when he is reported in EU

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het
3 comments
Read more