Skip to main content

630m/475kHz en ICOM IC706 Clasic

Met de IC706  USB dial 474.2   WSPR
behalve veel EU WSPR signalen

ook de CW ID hoorbaar van   AERO BEACONS  
"BIA"  "SA"  "RP"
origine onbekend

De IC706  gemodificeerd    MW tx enable  met restrictie low power  als signaal bron.
DL4YHF  gebruikt de clasic IC706 op 475kHz maar de modificatie dat mogelijk maakt
kon ik niet vinden.
Deze IC706 was aardig geavanceerd toen hij op de markt kwam zo'n 20 jaar geleden.
Geen firmware updates mogelijk het moest allemaal gelijk goed zijn dat is different koek.
Nog steeds niet afgeschreven op techniek well done ICOM!

Deze mod staat vaker beschreven maar  gaat over het VHF
Open the top of the radio by removing the 3 top screws and 2 side screws. Look at the radio with the front panel facing you.
Gently pull up the speaker and set is aside without damaging the speaker or the wires that attach it to the rig.
Note the silver rectangular box near the middle of the PCB marked something like "9 MHz SSB Filter".
Move your eyes up from this filter toward the back of the radio. Just before you get to the "D 108" marking,
you will see two tiny diodes, two blank spaces, and one additional diode. They look something like this:
                                               D105
          --D108--                           [  ]

           [   ]     [   ]    [   ]     [   ]   [XX]
           D60    D59   D58   D57   D72

 ?? D60  USA low power 50 MHz  (remove for 100 W output power)  ?? IC706

 D60  enable TX MW  i.e. 475kHz  ! SET LOW POWER
 D59  CPU Tx limit
 D58  Eur Fra 144-146 MHz
 D57  Den Fra 50 MHz
Op de onderzijde van de MAIN board de eventuele  French version   D84 D85  waren afwezig.

D59  had ik al eens verwijderd en de "yellow wire" mod had ook al gedaan
Om tx 475kHz mogelijk te maken moest ik  D60 verwijderen dat klopte niet met de beschrijving.
Met trial en error  om de juiste diode te vinden.
Op een gegeven moment had ik alle diodes verwijderd maar toen waren 50 en 144 verdwenen.
Door terugplaatsen van D72 kwam 50 en 144 weer terug.
D105  ook verwijderd daar staat op de PCB iets van  50W / 100W.
Op 144MHz ca 12W gemeten op een PM1300a SSB Electronic power meter.
op 50 en HF ca 90W draaggolf  dat was onveranderd.
Het 475kHz  signaal  is niet  mooi een 475kHz bandfilter zal nodig zijn.
En niet vergeten low power instellen.
Dezelfde constatering had DL4YHF ook.

Nu  alleen D72 nog aanwezig in mijn IC706 zie foto
zeer  kleine  SMD dioden  1x 1.2mm de 2 in het midden.
output op 50Ohm 475kHz ongefilterd x= 50uS/div 


475kHz signaal na  MF filter ca 4Vtt   niet 50Ohm  maar met 33pF  uitgekoppend  ca 2mS periode
de laagohmige koppel wikkeling van de MF trafo gaf slechts 0.2V tt op 50OHm


Comments

PE4BAS, Bas said…
Had laatst ook een kleine reparatie aan mijn Icom. Wat zijn die componenten klein zeg. Had een vergrootglas nodig om te zien waar ik mee bezig was. Signaal is inderdaad niet helemaal zuiver zo te zien op de scoop. 73, Bas

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...