Skip to main content

Propagatie reporter



De ene dag  ZL/VK decodes   de volgende dag niets
Het gaat sterk op en neer  eigelijk geen peil op te trekken  korte golf propagatie.

Gisteravond tot na middernacht USA  midwest  op 10m plotseling terwijl USA decodes deze week minimaal waren.
Vanmorgen veel decodes VK7 Tasmanie maar geen ZL's   
Alleen Zuidoost DL blijft openingen houden naar NieuwZeeland  
En natuurlijk Zuideuropa  daar hebben de aardmagnetische storingen haast geen invloed.
In zuid Europa is al vele weken lang 6m en 4m  open   zelfs Hawaii op 6m met OE lukte.
Er is een vrij scherpe rooi lijn over Europa ten noorden waarvan geen 50MHz propagatie is.
Ongeveer bij noord Italië begint de perma 50MHz ruis zone.  

De afgelopen week toch  nog  8x ZL  7x VK7 en VK3 VK5 VK8 
De slechtste dag was 21-4   haast blackout op 10  alleen FR en CX  decodes 

Ook jammer dat American Samoa KH8/PA3EWP expeditie precies na de super goede periode begon  ik heb ze alleen op 17m kunnen werken. Slechts zwak op 20 en 10m gehoord.
Het leek in Groningen allemaal nog zwakker dan elders.

80 en 160 haast niets boven 1000km 
maar een uitschieter op 160 
 2014-04-18 01:30  PY9MP  1.838094  -25  0  GH13dw  10  PA0O  JO33hg  9834  33 
 2014-04-24 02:54  PA0O  1.838106  -26  0  JO33hg  5  PY9MP  GH13dw  9834  240 

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het