Skip to main content

Austral TX6G III

Eigenlijk had ik het na FT5ZM een beetje gehad met de piles van DX-pedities
een QSO rendement van <0 aanroepen="" met="" nbsp="">
Maar TX6G heeft een heel sterk team van G operators  die kennen de problemen van noordwest Europa en doen hun best om door de muur van Italianen heen te luisteren.  Ik noem ze voor het gemak allemaal maar Italianen ..  de tegenpartij    
Vanavond  TX6G weer sterk op 28.030 CW   deze keer lukte het QSO wel
Ik moet voor het beste signaal de antenne  NW-ZO zetten
Ik denk dat het signaal over noord-west komt

Short path is 015   long path 140 graden volgens N1MM
Het is niet noord-oost  of zuidwest 

Vreemd deze richting ik had verwacht in de avond  zuidwest voor Polinesië
Smorgens  tot 12 uur wil het wel over zuidoost naar Hawaii soms maar dat is
een heel ander tijdstip.
10 was weer goed   FO4BM in SSB  op 28420 aanzienlijk zwakker dan TX6G
FO Frans Polinesie  is ca 800km ten noorden van Austral Island FO/A 
Dat lukte ook nog ondanks de pile  met veel hardere zuid-EU met name zuid Frankrijk.

Het kan raar lopen.
80m TX6G  dat is smorgens de beste kans
Op de webside  van TX6G staat dat ze veel sterkere signalen uit zuid Europa hebben  ook op 80m

LOTW  al bevestigd zelfde avond..

Next
 Call signWorkedDate/TimeBandModeFreqQSL
DetailsPA0OFO4BM2014-03-27 19:08:3710MSSB28.53005FRENCH POLYNESIA
DetailsPA0OW1AW/02014-03-27 18:51:4812MCW24.91226 
DetailsPA0OTX6G2014-03-27 18:39:5810MCW28.03202 
DetailsPA0OTX6G2014-03-26 06:14:1130MCW10.12506AUSTRAL ISLAND
DetailsPA0OHF15NATO2014-03-25 17:36:2410MCW28.01198 
DetailsPA0OW1AW/52014-03-25 15:45:0412MCW24.90204 
DetailsPA0O3B9FR2014-03-25 15:41:0817MCW18.07493 
DetailsPA0OW1AW/42014-03-23 16:58:2812MCW24.90544 
DetailsPA0OXE2ST2014-03-23 16:57:5812MCW24.91096 
DetailsPA0OP29NO2014-03-23 14:21:3310MCW28.00360PAPUA NEW GUINEA
DetailsPA0ORC80KEDR2014-03-23 00:48:13160MCW1.82500 
DetailsPA0OHS0ZKX2014-03-22 22:36:54160MCW1.81368 
DetailsPA0OTX6G2014-03-22 19:00:4110MSSB28.35100AUSTRAL ISLAND
DetailsPA0OCE6SAX2014-03-22 18:21:5410MCW28.00463 
DetailsPA0OW7SW2014-03-22 18:19:2510MCW28.00640 
DetailsPA0OW1AW/52014-03-22 18:15:1810MCW28.03660 
DetailsPA0OTZ6BB2014-03-22 15:12:4810MCW28.04570MALI
DetailsPA0OW1AW/42014-03-22 14:53:1820MCW14.03070 
DetailsPA0OW1AW/42014-03-22 14:33:4817MCW18.07283 
DetailsPA0OTX6G2014-03-22 14:31:1715MCW21.02213AUSTRAL ISLAND
DetailsPA0OTX6G2014-03-22 13:07:5912MCW24.89691AUSTRAL ISLAND
DetailsPA0OP29NO2014-03-22 12:53:2612MCW24.90350PAPUA NEW GUINEA
DetailsPA0OEA8OM2014-03-22 10:18:4310MCW28.01500 
DetailsPA0OW1AW/KH22014-03-22 10:14:3310MCW28.03097 
DetailsPA0OTF3W2014-03-16 21:46:4520MRTTY14.10850ICELAND

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het