Skip to main content

9M4SLL SPRATLY

Almost 30 years ago


tonight 9M4SLL heard at  160 wkd at 80 
 earlier H44G very weak at 80m
But al propagation seems shifted to South EU.
Signals are very weak and if something interesting is heard a lot of QRI  tuning and deliberate QRM makes you want to switch of radio.
If 9M4SLL  says OH1? OH1? again pse..
Then the pile just keeps the same...
everyone  keeps calling as if there is no relation with whatever 9M4SLL says
How different is this when listening to a pile of state side signals
There is no discipline in Europe plus deliberate jamming is common now at every DX that attracks HAM's A cluster spot and a zoo is starting. 

I must admit that it sometimes happens to me calling simplex when split is asked. The K3 split setting is lost when swapping bands. A short check at 80m and back to 160 a K3 owner has to check every time whether the K3 is still operating shift frequency before calling.
if not   CONFIG:SPLT SV is set to YES 
 bedankt Enno   ..had kunnen bedenken dat er zo'n optie was
An other thing is that sometimes the RX of the 2nd RX is gone. Then I do a power cycle to reset. After that the 2nd RX is back but VOX is of  and split also cleared.
I think split is now kept since SPLT SV=yes.
But it is easy to have a mistake in the situation.
But I will not join the police force  to make comments on that over the DX calling frequency that will only ad more QRM.
 The simplex calling om can make a tiny operating fault I do not necessary have to hear the om  but I will hear the stupid police for sure.
  

    Winter returned  in JO33HG

h



Comments

Enno - PF5X said…
CONFIG:SPLT SV to YES en split wordt per band onthouden ...

-- Enno, PF5X
pa0o said…
okay
Enno
dat had ik nog niet gevonden
tnx
pa0o said…
okay
Enno
dat had ik nog niet gevonden
tnx

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...