Skip to main content

DX index WSPR

28MHz   last 7 day  real good
selected on distance    top 100  all  above 16000km
DX index 100%
  
160 and 80  not a single decode >1000km  the low bands are real low these times
My 80m experiment with the loop was no improvement.  The vertical is still better but not good enough it needs more distance  from the mast. Will try a fishing rod.  Heard 3B9SP  very good last night on 80m not busy, no jamming  but with the vertical at only1m  from the mast the radiation pattern  is not good enough to be heard.
The 160m inverted-L  is more effective1/4 wave  is >> then the mast length and the radiation is not disturbed


 2012-10-17 08:04  PA0O  28.126171  -26  0  JO33hg  5  ZL3PX  RE66hm  18519  49 
 2012-10-17 08:54  PA0O  28.126169  -25  1  JO33hg  5  ZL3PX  RE66hm  18519  49 
 2012-10-20 07:24  PA0O  28.126165  -22  0  JO33hg  5  ZL3PX  RE66hm  18519  49 
 2012-10-20 07:36  PA0O  28.126164  -26  0  JO33hg  5  ZL3PX  RE66hm  18519  49 
 2012-10-20 07:50  PA0O  28.126164  -13  -1  JO33hg  5  ZL3PX  RE66hm  18519  49 
 2012-10-20 07:56  ZL3PX  28.126121  -3  -2  RE66hm  5  PA0O  JO33hg  18519  322 
 2012-10-20 08:02  PA0O  28.126164  -4  0  JO33hg  5  ZL3PX  RE66hm  18519  49 
 2012-10-23 07:46  PA0O  28.126123  -24  0  JO33hg  5  ZL2IT  RF80km  18312  30 
 2012-10-23 08:16  PA0O  28.126126  -13  0  JO33hg  5  ZL2IT  RF80km  18312  30 






       
                                                                    

    


                                                

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...