Skip to main content

some DX

28 is not what we are used too. T2T in the evening seems not possible. They are too late on 12m for us  only working USA 


But still some DX to catch

20111117 1751   7004,0 CW   PA0O         599  T2T             599                    
20111119 0842  28037,3 CW   PA0O         599  VR2UW           599 Ray                
20111119 0957  24897,7 CW   PA0O         559  9N7MD           599                    
20111119 1046  24945,0 USB  PA0O          59  9N7MD            59                    
20111119 1709  24910,7 CW   PA0O         599  FO/N6JA         599                    
20111119 1927  10108,5 CW   PA0O         599  ET3AA           599                    

50MHz
WSPR

 2011-11-19 10:40  PA0O  50.294581  -12  0  JO33hg  5  OZ7IT  JO65df  428  57 
 2011-11-19 11:56  OZ7IT  50.294477  -7  0  JO65df  5  PA0O  JO33hg  428  242 
 2011-11-19 13:02  M1DUD  50.294468  -13  -1  JO02qc  2  PA0O  JO33hg  377  68 
 2011-11-19 13:24  PA0O  50.294564  -22  0  JO33hg  5  M1DUD  JO02qc  377  252 
 2011-11-19 12:08  PA0TBR  50.294573  -15  0  JO22pi  5  PA0O  JO33hg  136  41 
 2011-11-19 12:10  PA0O  50.294518  -21  0  JO33hg  5  PA0TBR  JO22pi  136  222 

OZ7IT   still the best DX since the beam is up.

137.5 kHz last week 
 2011-11-17 21:36  G4WGT  0.137497  -26  0  IO83qo  0.02  PA0O  JO33hg  613  90 
 2011-11-17 19:06  M0PPP  0.137563  -24  1  IO93gm  0.1  PA0O  JO33hg  536  90 
 2011-11-19 16:14  PA3EGO  0.137507  -10  0  JO22mb  5  PA0O  JO33hg  172  38 
 2011-11-17 20:58  PA0A  0.137500  +10  0  JO33de  1  PA0O  JO33hg  24  67 

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more