Skip to main content

10m wspr this morning down to 200mW

 2011-11-05 06:58  PA0O  28.126024  -23  0  JO33hg  5  VK7AB  QE37ne  16905  84 
 2011-11-05 07:02  PA0O  28.126023  -16  0  JO33hg  1  VK7AB  QE37ne  16905  84 
 2011-11-05 07:14  PA0O  28.126023  -23  0  JO33hg  0.5  VK7AB  QE37ne  16905  84 
 2011-11-05 07:26  PA0O  28.126022  -29  0  JO33hg  0.2  VK7AB  QE37ne  16905  84 
 2011-11-05 07:38  PA0O  28.126022  -28  0  JO33hg  0.2  VK7AB  QE37ne  16905  84 
 2011-11-05 07:46  PA0O  28.126022  -28  0  JO33hg  0.2  VK7AB  QE37ne  16905  84 

The mornings before 1W was enough for ZL1JA and ZL2RF

this evening could catch 3D2T at 30m CW  and 
E51NOU  South Cook ZK1  In a big W-pile on 28.009.9 CW
E51NOU Bill van der Heide was waiting for his flight to North Cook. I was copied as PA0OPA   A miss-copy  that happens ofther with my 1 letter suffix.
I had that with TL0CW Rudi on 80m CW   firts he got my call correct. But then he added an extra letter to it..
And to correct an extra letter  is difficult in CW with low signals and high QRM.
 


Jaap,
Yes, you are right about my miscopy. I will correct my log. You were also very weak and of course there was the usual qrm, but I should have realized it was you.
My flight to N Cook has been delayed until the end of the week. Until then I will be in S Cook and signing E51NOU. I will have a different callsign for N Cook.
73 Bill

I send Bill this text, I'm hoping  for some activity from exotic locations ...

One question
would you be interested in running WSPR beacon from your exotic QTH?
When  your radio is idle ?  you could run 1 or 5W WSPR 28MHz?
You would be almost the only one there in the whole Pacific except for KH6 there is noone!

If you can run digimodes like rtty /psk with your rig and PC  it is very simple to setup
and the results are amazing!

f.i. today  I reduced 28MHz to 200mW still VK7AB copied my signal

WSPR is  a full automatic receive / transmit system  developed by  Jim Taylor K1JT
genius!   low power vy small bandwidth  200 cycles for all  stations on 28MHz
and it works while you can not be in the shack /home  or have something else to do..
Still  you can use your equipment

it is worth trying


 

Labels:

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more