Skip to main content

Re-using Molex PC connectors

Our summer weather ended this afternoon with heavy showers and 17C only.  HF propagation has been very disturbed. No decodes by VK7DIK on 80m last night it seemed to be restored. But only temporary, this evening again no grey-line decodes.
I had to move the Steppir control-box and rotor indicator to the shack. So did not have to be bored. Painting outside was not possible unfortunately ;-)


The PL259 as  tool to disassemble the PC power connectors..

The Molex terminals fit as plugs and sockets in this connector.

The Kenpro rotator that belongs to the Versatower  has a strange type connector ... 10 pole  idiot proof.
This old rotor has 6 wires. 3  for the indicator  and 3 for the motor.  
The voltage  of the  potentiometer in the rotator is simply displayed as 0-360 degrees by the voltmeter in the indicator.


My own newer type KR-400RC  uses 5 wires   2 for the potentiometer and also 3 for the motor.
The indicator has a  360dgs 500ohm potentiometer same as in the rotator. Both are part of a Wheatstone bridge. The indicator motor drives the scale to  balance.


I had to find a way to extend the rotor cable with 30m extra without modifying the connector.


The only plug that fits to this pins where the Molex power plugs used in PC's. I had some in the junkbox.
This Molex type connectors are ingenious simple and high reliable.
They where developed by Molex in 1950.

Now both controls are near the radio. 
The Steppir cable  was already about 30m long is extended to 60m using a cable with 25pole D-connectors. The cable is 0.25mm²  15 wires
It seems to work okay without extra Voltage boost.
The moral of this story do not clean out your junkbox too soon. 




Today morning 28MHz was good many decodes of VK2KRR (100W) and VK5AKK (10W)  and heard with 5W by both.
Also FR1GZ many decodes  T61AA & A45SWL  
But later ST0R was very weak and working  south EU only.





Comments

Sunkye International Co.,Ltd said…
Great and useful article. Creating content regularly is very tough. Your points are motivated me to move on.

Nano-D connectors

Micro-D connectors
May 24, 2017 at 9:46 AM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...
3 comments
Read more