Skip to main content

Made an active antenna to compare

To compare with the K9AY loop i made a small active antenna  
to the concept of PA0RDT  http://yu1lm.qrpradio.com/pa0rdt%20whip.pdf
I used a strip of double sided copper  clad  epoxy print 200x30 mm.
The amplifier is a FET  U310  and  2N3053 emitter follower.


This small capacitive antenna  did fit in a cycle bidon (bought on the Alp de Heuz once..) 
Interesting this antenna  is only picking up the Electrical-field. 
It is also a good RFI sniffler.


I used a relative big pickup plane of about 3x20cm  at the risk of IMD but i wanted to compare this E-field antenna on the 137kHz and 500kHz bands.








It works but the DCF39 TX at 138.9 kHz is about 30B stronger on the K9AY Loop. I have to check that out the difference should not be that big.
That was at the low position (top picture).
I moved it on top of the house about 8m a.g.  
Now DCF39 138.9 is s9+30   the difference is about 20dB in disadvantage against the loop. The high position gave 10dB more signal. I have heard OK2BVG good on 502kHz.
The higher bands give S9 noise  to much signal for the IC706  the preamp has to be switched off. Heard DL/KL1A good on 40m with it... 
It is better than nothing... but i compare it with a real good loop in the open field.
It has the advantage that it is very small and wide-band.
A good travel companion.









  

Comments

Bert, PA1B said…
Hallo Jaap,
Dat ziet er goed uit op de foto.
de mini-whip is een interessante antenne.
Ik vraag mij af of 200 x 30 mm niet véél te groot is. Ik meen mij te herinneren, dat het kopervlak ook maar iets te groot wordt, dat er dan intermodulatie optreedt.
De versterker is immers héél breed.
Ook EPO in je bidon brengt dan geen uitkomst meer. ;-)
Succes, Bert PA1B

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...