Skip to main content

28MHz was.. real open


Jim-san JG1KGS   operates  VQ9JD   in  WSPR  also on top band  and 80m      nice  activity  160 and 80m  and higher bands

2011-04-05 22:50  PA0O  1.838014  -25  0  JO33hg  5  VQ9JD  MI62er  9098


Lots of VK on  28MHz  copied every morning.  The VK's have really got the taste for WSPR   also on 6 and 2m   


Just 1 day later not a single VK on 10  and 80 / 160 as dead as a doornail...


Just this Friday again VK7DIK  did decode me again 80m around grey-line time

Comments

PD7BZ said…
Hoi Jaap,
De 10M band is echt erg goed open.
Afgelopen 2 weken erg leuke DX kunnen werken met als uitschieters NH7O,9N7AN,5M2TT en vandaag zelfs XV1X op CW.
Ook was XU7 erg sterk op 10M in CW.XV2RZ was erg goed te horen in SSB op 28505,maar hoorde mij niet,hi.
Verder met regelmaar VK en YB te horen en ook soms wel te werken.

Dus al met al is de 10M wel een band die in de gaten te houden is.

73's Bernard PD7BZ

Popular posts from this blog

SPF5189z Low noise preamp 23cm

14-4-2018 updated


Above the low noise  preamp 50 - 4GHz    ebay  6€

Tested  2 small porto antennas
1 Baofeng UV antenna left   2nd best signal on PI2NOS
2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected
3 piece of wire :   best signal in the setup...

Unit under test at workbench.
It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA
And i could  no longer adjust it with the negative bias Voltage.
The - Voltage went to zero and the SPF input port became low Z.
This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench.

The specs of  SPF5189z  say it has an internal circuit  regulating the bias current.
Replaced . again   with an other of the 5 spare SPF i have.
The new one again could be adjusted at 50mA  5V 
The current raises to 150mA  when removing the  negative gate voltage.
Where is that internal bias circuit ?
I suspect  eBay …

2011-01-22 DIAMOND X30 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this Diamond collinear 70/2 combi antenna at a height of 25m. I needed to investigate what could be wrong.
Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E
The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size but it is no longer selling i think. This H43
3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire.
With this dipole the signals where totally worse. So the Diamond does work?
I got curious to look inside. Maybe moisture penetration degraded the antenna.
This  antenna is rainwater close in its normal vertical mounting position. But take care if your mast can b…

Nice opening10m and 12m to S.A.

SFI  low 70 a 16 K3  still 10m opened up in afternoon to N-Italy EA5 F JN33
F/PD0OHW/M in JN33 decoded 150mW

VP8LP  12m    2-way with GP 7m ag swr 1:3


60m 5,362 open to ZL every? morning