Skip to main content

oooowwww very bad propagation this weekend on the low bands

On 500kHz   only 1 USA report from EU  ....me ;-)


2011-02-27 05:18
 WD2XSH/7  0.495969  -27  0  EM31js  20  PA0O  JO33hg  7830  39



Only 1  decode  against 16 previous nights
160m yesterday evening and night   not a single DX over 3000!
much later  some USA decodes
I have never seen such poor propagation since i have been on with WSPR
80m the same
in the top DX list   no EU  present  no VK to EU 


One time i tried to make a sort of DX-index for JO33
I select 100 records descending on distance over 24hours  and  count  the DX>4000
Most time my Index is well above 50  But now it was zero on 160 and 80m until long after  midnight very unusual.  



2011-02-27 06:08  PA0O  3.594140  -16  0  JO33hg  5  WB8HWF  EN80sc  6497
 was the best  DX  decoded   normally   VK6  or VK7DIK  
 the best DX decode  in EU was W to south DL
The other EU decodes in the list are erroneous.
The best band was 28MHz  with VK6TQ and VK6GOS 
15m also poor
The conclusion is that we where lucky last 2 weekend  it could have been much worse.
So it was very clear to me right away that propagation was changed dramatically .
But no one made any remarks about it!  very strange !  Everyone at the WSPR  chat  seemed to find this dramatic free fall of propagation normal???      


My other .. sometimes conflicting hobby
This morning  I decided to go for a "training"  cycle trip...  

Until now I  always invented an excuse not to go.
But no radio event or QRL trip and absolute boring propagation so... no more excuse
It was a cold fog this morning at 8 am  I decided to use my special hi tech thermo socks waterproof...
And not my neoprene Sleeves... a wrong decision  as I found out painfully.
After 20km it started to rain cold rain snow almost.  We got totally soaked  and i got very cold feet and legs.
We decided not to do the long trip 100km rounding the Lauwersmeer   Zoutkamp was our turning point only 75 km.
It has been some years that I have been so freezing cold.
We had to recover  with warm jars and shower.
Now it just started to snow ...


I have installed  Ham Radio Deluxe V5  on this XP machine  works good
I want to have complete remote control over my K3 i am new to HRD i tried it on my laptop W764pro but it did crash XP should be no problem.
Now  can control it with my mobile phone  and  the beta version Teamviewer for Android 
It is just unbelievable...
I have not found out if there is another way i like an HRD web-server.  Teamviewer has the advantage that it goes trough most routers and firewalls without anything to configure.
It is real good software. Download it and it works. It is free for private use but expensive to licence  1000€ or so. 


But my station it needs  remote controlled Antenna switch / tuner.
I have the ACOM1000 only using it sometime in DX-pedition pileups.
The ACOM is a beauty PA but  has only the conventional 1 in 1 out connection and no CAT control.


Now i can use the ANT1  ANT2  of the K3 
I have my 80m vertical on ANT2  and the 40-20-15-10  dipole on ANT1  or I have to swich manual to the 160 vertical at the cost of 15 and 10m for WSPR.
Receiving  can be selected to the RX ANT  alternative  the K9AY loop   for 500kHz f.i.






































    



Comments

PE4BAS, Bas said…
Jaap, het was geen weer om te fietsen joh. Hoop dat je er niet ziek van bent geworden. Het was beter geweest het NAT te bezoeken, daar was het warm en droog. Ik heb teamviewer ook gebruikt en me een ondersteunende telefoon lijkt het me ook te gek om zo de set op afstand te bedienen. Helaas heb ik nog een oude JAVA telefoon, dus dat feest gaat niet door. Maar wel regelmatig met de laptop. Deed het in verleden ook met NTR connect, ging ook prima tot ze hun beleid aan pasten. Laatste tijd probeer ik logmein, maar dat is hier zo traag als stroop. Denk dat teamviewer nog het snelst is momenteel. 73, Bas
Anonymous said…
Hmm, that?s some cool information. I would search on Google to find other relevant articles. Actually, I came across your blog on Google Blog Search. I?m going to add your RSS feed to my reader. Continue posting please!

cheap nolvadex

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het...