Skip to main content

160m surprise


unexpected reply on cq test 100W 
hoping for some points in EU  and then 2 strong USA  ham answered
20160116 2346   1831.5 CW   PA0O         599  246  KD6UO           599   002        3
20160116 2348   1831.5 CW   PA0O         599  248  AA6RR           599   002        3

AA6RR was  from Maine
KD6UO from CA?  hard to believe in the present lack of propagation
But today received direct QSL 




Comments

Steve McDonald said…
If you Google KD6UO you will see that he is a longtime "remote station" operator. i suspect that he worked you using a remote, probably on the east coast. His QSL should really indicate this location if that was the case. There has been no EU prop from west coast on 160 this winter as far as I know.
January 28, 2016 at 8:14 PM
Steve McDonald said…
As well, the sun has still not set at 2346Z in California. Looks fishy.
January 29, 2016 at 5:03 PM
pa0o said…
right you are
the card is real...
But a 160m band qso with California DM07
path in broad daylight at that time
that is impossible ...


but it was a good signal for Maine
February 8, 2016 at 6:42 PM
Unknown said…
Wow!
Thanks to my friend Chip W1YW I was alerted to this misunderstanding. Yes, I am a remote station operator. In this case, I used the RHR service. My LoTW entry properly documents the contact from NY FN22.
I must admit that this is the first time that my card data has been brought to my attention as an issue.
Jaap, could you please send me a return QSL card or upload the confirmation to LoTW?
As I recall, I included 2-3 dollars for return postage.
My email address is roger@rodagroup.com!
Thanks!
73,
Roger
February 24, 2016 at 4:15 PM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...
4 comments
Read more