Skip to main content

BA7IO 160m

BA7IO Vange 160m  
Nice signal tonight  1822kHz up1


Tonight I removed the 50MHz yagi again.
I wanted to see if any DX would slip through to the north  but it did not.
The weather forecast is only storm and rain.
Many decodes 6M WSPR of OZ7IT  PA0TBR M1DUDevery day but noone else QRV at reasonable distance.
No UA9 SWL  or any other Rusian at 6m  unfortunately.
 summary   6M WSPR last 2 weeks    the first one is an Freudian misdecode..
 2011-12-07 11:10  PA0O  50.294415  -17  -1  JO33hg  0.5  VK5ZRL  PF95gc  15771  81 
 2011-12-02 20:36  G6AVK  50.294416  -26  -1  JO01ho  5  PA0O  JO33hg  447  63 
 2011-12-04 09:38  OZ7IT  50.294482  -7  -1  JO65df  200  PA0O  JO33hg  428  242 
 2011-12-05 16:14  PA0O  50.294467  -23  -4  JO33hg  5  DF0ZDF  JN49cx  382  163 
 2011-11-30 13:44  M1DUD  50.294471  -11  0  JO02qc  2  PA0O  JO33hg  377  68 
 2011-11-30 22:32  PA0O  50.294514  -18  0  JO33hg  5  M1DUD  JO02qc  377  252 
 2011-12-01 17:54  PA0TBR  50.294432  -27  -1  JO22pi  10  PA0O  JO33hg  136  41 
 2011-12-01 18:16  PA0O  50.294499  -23  -1  JO33hg  5  PA0TBR  JO22pi  136  222 
 

I had  some shorts between the inv-L wire and the 7el LFA  the wind blew the wire against the beam.
I can still use the Steppir at 6m  but  have to solve the high SWR problem first. Receiving seems good.
Possible one part of cable must be replaced.
I can work it in the dark the beam is lowered on the driveway and good light.
Only the rain and storm has to pause a bit...



Comments

PE4BAS, Bas said…
Jaap, dit is eigenlijk niet de tijd van het jaar voor antennewerk. Maar ja, tijdgebrek en toch willen he! Ik wil ook nog een antenne opzetten voor de 10m contest komende weekend. Hoop dat het geen windkracht 10 word vanmiddag want dan begin ik niks. En het moet ook droog blijven, maar ja.....we hebben het niet voor het kiezen. Leuk je nog even te werken in de 10m RTTY contest. 73, Bas
pa0o said…
Ik was pas laat thuis uit DL de voorspellingen zijn niet te best
Gisteravond was het wel goed te doen.
Ik ben ook niet klaar voor de arrl10m moet nog wel aan gewerkt

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...