Skip to main content

CQ160CW CW alive and kicking

 I choose to enter the low power 100W max. contest section.

  K3 i-L 25m vertical and rx Beverages E/W

Since in our ADSL2+ network a "notch" is set by the KPN network provider,what a relieve! finally.
TX-ing 1.8MHz  is without interfering our network TV. Did you know that  ADSL2+  is using 1-2 MHz base band ? The KPN helpdesk man and woman do not know this. Friendly people but they are schooled in "communication" that's how they call it in the University and schools it has nothing to do with technical communication but it is a sort of training to build a pleasant buffer between the public and authorities in general, many good job's to get in this field !   Thanks to a real KPN technician the ADSL2+ carriers within 1.8 -  2.0 are switched off, called a notch. This is the only way to get rit of 1.8MHz RFI in the network all other methodes failed.
My result at Sunday morning band close
 630Q  ZF5T XE2X 2-way great receiving !
 75 multi's 17 states 
Poor propagation overall , some "strong" W  early night,  E2X  JH4UYB heard well, but i had chosen for low power section being in underdog position in the piles and depending on good receiving of the competitors. 
And most time i was S&P in a very crowded band , later i moved to the higher part of the band at about 1856 to 1875 our band limit is 1810-1880 ,  1850 is a LSB phone frequency and some typical hams persistently want to have phone chats in the middle of this major 160 CW contest, no other frequencies available it seems... If you start by mistake a CQ near this frequency with no one using it you are corrected by the band police.. 
of coarse they are in their right but stupid it is.

  40m foldback dipole with ice on the wires this morning
and a part of the i-L 160m


DX Highlights: ZP5X XE2X   E2X VR2XAN   despite the  blind tale callers over pending QSO's  
Hard to believe but E2X heard my low power in a peak of signal and  rare break of constant callers. 
PA0OE2X2021-01-31 20:33:27160MCW1.81544THAILAND
 but it is confirmed!

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...