Skip to main content

HANTEK DSO5102P

Looking for a digital storage oscilloscope
Saw the HANTEK DSO05102P at Banggood  with good review
100MHz  or as some review said factory unlocked 2nS 
212€ free shipping !
it arrived in about one week from China very quick.

Some reviews showed a damaged package  missing parts
It is always a bit of a gamble how it will arrive.
My package was bounced but wrapped in plastic no lost parts.
No import fee this time also a bit of a gamble.
Power on, display came up it seemed okay .
But the 1kHz 5V test signal  did not display for both channels
Just a straight line with quantification noise and some spikes when turning the V/dev knobs
Had email exchange after a few days problem solved.
A loose ribbon connection due to transport ? the pre-amp had no 5V supply.
Sending back is no option and there is no EU agent as far as I know
Hantek treated me generous with a refund to compensate repair costs.
But repairing equipment in The Netherlands/EU the official way,
can easily exceed the purchase prize due extreme tax load on everything.
Looks well build internal with metal shielding
After fixing this i was lucky to have  the 1kHz test signal displayed.

The performance is very good and high value for €.
Bright 800x480 display   2nS /dev  1mV/Dev
Easy to operate light weight.
Small footprint on the desktop  w32x  deep 12cm.



                                                  just a straight line  no V-amplifier

                                           left 6-p connector was the failure
                                                          okay!

Comments

PE4BAS, Bas said…
Dus nu een gratis scoop? 73, Bas
pa0o said…
40€ retour ook nadat ik netjes gemeld had dat de fout hersteld was.
Laten repareren voor 40€ is geen optie

maar toch risico er is geen garantie


Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...