Skip to main content

CQWWCW weekend


2018 CQWWCW  
A lot of CW practice again after been spoiled by FT8 DX
lot of interesting DX locations present in this major contest!
 28MHz closed  although ....2 decodes today !!
0924 -15 0.1 28.126009 -2 VK3KCX QF22 47 16386

 started the contest late Saturday afternoon
rig K3 100W 
3 ele 10m      15m(bad SWR) 
20 40 rotating  dipole
80 inverted V dipole
160 vertical i-L 
receive Beverage east / west  360m

        Band     QSOs     Pts  ZN   Cty  Pt/Q
         1.8     151     212   11   39   1.4
         3.5     301     388   16   58   1.3
           7     346     692   30   79   2.0
          14      78     183   20   34   2.3
          21      25      75    5    5   3.0
          28       1       1    1    1   1.0
       Total     902    1551   83  216   1.7

Could work most DX / multy heard  with 100W
But E2A E2X B4T YE1K heard long time CQ with very good signals at 40 80  Guess too high QRN levels there.
160m PJ2T heard  and some other nice DX that could not copy me

Good USA signals at 160  even responding to CQ,  
Best band 40m real good lot of USA including zone 3

with low power one has to be patient..
and i like to search for the DX well hmm search it is all presented 
conveniently  by  N1MM but it is worth to search the band yourself
as not all DX is on the cluster spot, and if it is, the spot frequency will be terrorized.
Call signWorkedDate/TimeBandModeFreqQSL
DetailsPA0OPJ4A2018-11-25 21:46:2740MCW7.06142
DetailsPA0OPJ4Q2018-11-25 12:37:2720MCW14.08694
DetailsPA0OPJ4A2018-11-25 12:27:0820MCW14.05027
DetailsPA0OPJ2T2018-11-25 02:52:0980MCW3.54945
DetailsPA0OPJ2T2018-11-24 23:06:2340MCW7.03131

DetailsPA0OZF1A2018-11-25 03:48:03160MCW1.81583

on CQ !  most Chinese seem to be running station ,was never called on CQ ,big signal
DetailsPA0OBY8AC2018-11-25 23:20:0940MCW7.06707










Labels:

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...
4 comments
Read more