Skip to main content

Dag van de Radio Amateur Apeldoorn


Zaterdag 10 november
Veel gezien veel om's getroffen  was zeer de moeite waard.

Een opvallend zelfbouw project was de MCHF  SDR tranceiver
3 kleine juweeltjes  van zelfbouw ,met verbazing gekeken zo mooi gemaakt.
Schitterend in  glanzend aluminium behuizing
Op zelfgemaakte freesmachine van PA0KN
de foto is helaas niet zo goed.

Nieuwsgierig geworden naar dit project  kwam ik op de mooie site van  M0NKA 
http://www.m0nka.co.uk/

M0NKA   Web 4m ontvanger getest en die werkt 

Met  de 4M  2 ele   DK7ZB 223   mini 3 bander ( fb fb !)
  zowaar gelijk een decode  over     616km   is misschien wat te veel 
4 spots:
TimestampCallMHzSNRDriftGridPwrReporterRGridkmaz
 2017-11-05 07:12  PA0O  70.092423  -25  -2  JO33hg  10  M0NKA  IO92ak  583  264 
 2017-11-05 07:16  PA0O  70.092426  -22  -3  JO33hg  10  M0NKA  IO92ak  583  264 
 2017-11-05 07:18  PA0O  70.092423  -20  -2  JO33hg  10  M0NKA  IO92ak  583  264 
 2017-11-05 07:30  PA0O  70.092435  -23  0  JO33hg  10  M0NKA  IO92ak  583  264




                                   
 630m last night 4 USA stations heard,   rare W3LPL  broke the 6000km barrier 
only the  2nd time this season
2017-11-05 06:26  W3LPL  0.475692  -27  0  FM19  5  PA0O  JO33hg  6217  46 

and Bob  2-way 160
 2017-11-05 05:26  PA0O  1.838031  -24  0  JO33hg  10  K4RCG  FM08si  6392  292 
 2017-11-05 01:34  K4RCG  1.838102  -22  0  FM08si  10  PA0O  JO33hg  6392  45

Labels:

Comments

Radioclub said…
Hello Nice SDR Thank You. TB9BCD
October 5, 2018 at 12:05 PM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...
4 comments
Read more