Skip to main content

First 6m ES signal 2017

50MHz  OY es

2017-05-04 06:40  PA0O  50.294598  -19  0  JO33hg  2  OY1OF  IP62oa  1254


23cm:

2 local QSO's PA0T  and PA3EKM
4 beacons copied every day
G3MHZ  1296.830    JO02pb
OZ7IGY  1296.930    JO33wm       CW and IP  ID
DB0VC    1296.920   JO54if
PI7ALK    1296.916   JO22ip    fsk  cw id  tjirpy  no yet at http://www.mmmonvhf.de/bcn_map.php


23cm   WSPR  ON5KTO  first decode ever at 1296.500 USB
lots of Doppler airplane reflections

Have to isolate the PLL 1050MHz pll
Now it is drifting a bit and 100Hz lower then at room temperature

the IC706 reports the 146.501500 MHz i.f. at WSPRnet.org
WSJT-X can report the 23cm TX frequency if the i.f. offset in my XVTR  -1.150 is set
nice feature  this is not possible in N1MM+  as far as I know
 UHF contesting  often using transverters  that would be a nice option




1296.830 GB3MHZ  JO02pb  signal here with airplane traces all over
USB dial 1296.828400  (i.f. 100Hz too low )


Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...
4 comments
Read more