Skip to main content

474.2 kHz night

TX  20%  and RX  active this night
Antenna current indication  over 100%  highest indication i got
The matching is closer to 50Ohms  less losses in coils and tuner
25V  4A
The IRFP4227  seems indestructible at 24V

2 marginal decodes of my QRP signal

 10dB lower snr   on the TX side.

strongest   of 18 decodes
2017-03-17 01:44  WD2XSH/17  0.475640  -8  0  FN42pb  5  PA0O  JO33hg  5630  49

5 decodes both
2017-03-17 03:52  WG2XKA  0.475721  -21  0  FN33lq  1  PA0O  JO33hg  5656  49
 2017-03-17 03:44  WG2XPJ  0.475694  -23  0  FN34lp  1  PA0O  JO33hg  5587  50 

 2017-03-17 01:24  WG2XKA  0.475721  -29  0  FN33lq  1  PA0O  JO33hg  5656  49 
 2017-03-17 00:28  WD2XSH/17  0.475640  -18  0  FN42pb  5  PA0O  JO33hg  5630  49 
 2017-03-17 03:34  PA0O  0.475614  -30  0  JO33hg  0.2  WD2XSH/17  FN42pb  5630  290 
 2017-03-17 02:58  WG2XPJ  0.475694  -25  0  FN34lp  1  PA0O  JO33hg  5587  50 
 2017-03-17 03:16  PA0O  0.475614  -28  0  JO33hg  0.2  N1BUG  FN55mf  5297  293 


DX peditions   are very active some more band slots
20170316 1039  14024,0 CW   PA0O         599  5U5R            599                     
20170316 1102  14017,0 CW   PA0O         599  9N7EI           599                     
20170316 1909  10106,0 CW   PA0O         599  9N7EI           599                     
20170316 1926  10104,0 CW   PA0O         599  5U5R            599                     
20170316 1931   7003,0 CW   PA0O         599  5U5R            599                     
20170317 0054   1830,5 CW   PA0O         599  9G5X            599                     



Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...