Skip to main content

6m / 4m ES op Konings dag

1e keer dit jaar voor mij   vroeg dit jaar
Rinze was op Kreta   goede keuze  gezien de winterse temperaturen hier
ijsmuts op  op Koningsdag  maar wel zon   ondanks de code oranje ...


op 4m was  SV


1.2016-04-2717:276 mMacedonia Z32KFSSB59
2.2016-04-2717:226 mMontenegro 4O4ACW599
3.2016-04-2716:496 mGreece SV4FFKkm19ljCW559
4.2016-04-2716:476 mCrete SV9/PC5CCW599
5.2016-04-2716:346 mMontenegro 4O7CWCW599
6.2016-04-2716:336 mGreece SV1CQNCW559
7.2016-04-1007:4417 mTurkey YM3KMCW559
8.2016-04-1007:3315 m VK0EKCW599
9.2016-03-2719:27160 m VK0EKCW599
10.2016-03-2617:4940 m VK0EKCW599
11.2016-03-2617:4080 m VK0EKCW599
12.2016-03-2517:4130 m VK0EKCW599
Mijn oude 1980 1296/144 transverter is weer terug  van Jaap PA0T 


  

SSB RX-converter  de oorspronkelijke AF239  RX converter was te slecht

PA2DOL  4 x 2N4944 om op 2C39 stuurvermogen te komen 
daar kreeg ik maximaal ca 5W uit
anno 2016  is er op UHF gebied veel te koop
Een goedkope smd  PD85004  LD FET  die van 70mW in 1 trap  ca 2W  kan maken 


en vele andere SS oplossingen om een 2C39 te vervangen.

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het