Skip to main content

CTCSS PI2NOS met de IC451E


De 70cm FM activiteit is enorm toegenomen sinds de relais PI2NON PI2NOS landelijke dekking hebben en ver daarbuiten 
Een fantastisch systeem en website! http://www.hobbyscoop.nl/ .
de relais staan o.a. op 349m !tx /rx ASL IJsselstein  en Smilde 302m asl !
Met een porto is heel Nederland bereikbaar. 
En via Echolink Wereldwijd  b.v. PJ4NX Peter is regelmatig te horen.
De oude ICOM IC541E  kwam niet meer op PI2NOS sinds CTCSS 88.5 is ingevoerd om de interferentie verminderen. De ingang van PI2NOS 431,725 MHz is tevens de ingang van DB0ET 
Emden  S9+ in Zuidwolde  uitgang 439,325Mhz
deze gebruikt 1750Hz ik kan hem met 1W openen.
Dus Groningse stations blokkeren / storen DB0ET als er via PI2NOS gewerkt word men werkt aan een oplossing.
Ik begrijp niet hoe CTCSS  deze interferentie kan oplossen?
CTCSS staat voor Continuous Tone Code Squelch System 
Ik zocht naar CTCSS optie.
Hobbyclub Veron Meppel had bouwsetjes ooit hiervoor
Ik heb er zelf eentje geknutseld 
ontwerp VK5AH  met PIC16F84 schema PD0DEF
overgetekend met Scheme-it van Digikey

2018 met dipswitch


Zo klein mogelijk gemaakt is toch nog groot door de onderdelen.  De PIC16F84 is niet kleiner

De BCD encoder (Van Dijken) heeft 10 BCD codes met 4 uitgangen 2 dipswitches maken 6 bits code Deze schakeling kan met 6 bits 64 tonen genereren.  4MHz X-tal afgeleid.
Het origineel maakt gebruik van een 6-polige dipswitch.
Een BCD draai switch leek me mooier. 
Maar de 6-ingangen zijn negative logica met interne pullups
Dat betekend dat de BCD codes van de switch omgekeerde logica moeten hebben.
open 1 gesloten 0  dat betekend dat 88.5Hz met BCD stand 6  en beide dipsw 0
2018 nav PI3UTR 145.575 CTCSS 77Hz heb ik de BCD schakelaar vervangen door dipswitch
en de opbouw aangepast

code 0001001 = 88.5 in de tabel van VK5AH
                    11  10  9   8   7   6
 TONE  FREQ        RB5 RB4 RB3 RB2 RB1 RB0
       000  1750 Eu Tone  0   0   0   0   0   0
 001   67.0         0   0   0   0   0   1
  002   69.4 *       0   0   0   0   1   0
 003   71.9         0   0   0   0   1   1
 004   74.4         0   0   0   1   0   0
 005   77.0         0   0   0   1   0   1
 006   79.7         0   0   0   1   1   0
     007   82.5        0   0   0   1   1   1 
     008   85.4     0   0   1   0   0   0 
     009   88.5     0   0   1   0   0   1 
kleine misrekening maar zo gaat het ook  88.5 Hz is voldoende
6 dipswitsches selecteren wel alle 64 codes.

De 88.5 blokgolf op 1 RA2 gaat door het  R1 C6 RC filter dat maakt er een driehoek signaal van.




De schakeling geeft de subtone zodra de 5V aanwezig is met de PTT vast aan 0.
De eenvoudigste manier is extern via de ACC aansluiting van de IC541E. 
Maar dat werkte niet het leek even te werken door de verhoogde condities kwam ik blijkbaar via een relay zonder CTCSS binnen.
Met het invoer punt achter de mike preamp werkt het wel.
Q13 de emitter volger op R48  bovenkant  blank maken  via een 100n C draadje naar een van de spare tulp plugjes 
De meeste versterking zit in IC2A  het hoogohmige ingangs punt op de basis van Q13 daarachter is minder gevoelig voor brom. Het lijkt nu wel goed te gaan IC2a blokkeerde de sub toon. 
Ik zou om het netjes te doen nog ergens een Molex busje kunnen toevoegen er zijn nog open plaatsen.
Maar de reserve tulp gaat ook.
  
  IC451E 
s3 draadjes met Molex pennen.
pin8=gnd 
pin5=88.5 audio subcarrier ( via 100nF niet op schema)
pin4= + 8V  TX 5mA max

 de CTCSS module trekt 6mA  maar dat gaat nog goed





Comments

Tjeerd, PA3GNZ said…
Jaap,

De toon moet inderdaad continue mee gezonden worden. Als het goed is moet deze aan de ontvangst kant niet hoorbaar zijn.
Heb je het signaal op het juiste punt geĂŻnjecteerd?
pa0o said…
Tjeert zou die subtone amplitude gemoduleerd moeten worden dan is de brom in FM onhoorbaar.

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...