Skip to main content

Juli UHF contest PI4GN Rottum JO33ii

Vanuit het  QTH bij  Nanko in Rottum JO33II
was weer PI4GN  actief in de juli contest UHF SHF

10GHz  ging als een speer    via regen scatter  een pileup! van OK stations
De logging was op 3cm nog op papier  dat is geen probleem met  paar verbindingen op die band meestal.
Maar nu ging het  nog beter dan 23 !  Volgende keer toch maar een logger ?
Of was dit een unieke contest  met zoveel sterke regenscatter Aurora klinkende signalen.

https://www.dropbox.com/s/43maz7nb9p238hj/VIDEO0091.mp4?dl=0

Zelf was ik gast operator 432MHz voor CW  ondersteuning op zondag
Zondag waren de condities en vooral activiteit wel wat ingezakt.
Deze keer geen OE3C voor mij.. het mooie was zaterdag al gewerkt  er was zelfs  een 432MHz QSO met Italie !
Ik hoorde OL1C op 23cm 1296.235  en DO/OM0A JN59 maar doof ..
Op 70cm  een SP station  nog wel op zondag
Omstreeks 1500 zondag uur kwam er niets meer retour en hebben we het station voortijdig afgebroken.

Maar dit was een topper voor 10GHz   veel OK OE F
70cm is wel voor verbetering vatbaar  maar 23 13 6 10 draaide top met de XVTR  preamp en PA direct achter de parabolen.
Met behulp van actuele ( Uffe) weer radar beelden ondersteund kan het scatter punt worden bepaald.
Tevens is de band op een waterval panorama beeld zichtbaar.
Regen scatter klinkt sissend als ruis gemoduleerde signalen. Zichtbaar op het spectrum beeld als bredere sporen. Zoals ik dat ken van WSPR bij aurora storingen.
Door het Doppler effect waaiert het spoor uit.  


Peter PA2V op 10GHz had zelfs een pile van OK's te verwerken.

via deze drie minuscule  spoelvormige stralers in een open blikje word de schotel "belicht"
voor 3 frequentie banden 23 13 6 cm golflengte

23 13 6cm transverters met SS PA  ca 40W 10GHz en preamps direct aan de 2M parabool  gemonteerd 
2 parabolen draaien onafhankelijk met 2 rotoren eigenbouw en een con-centrische rotorbuis
knappe constructie  alle UHF SHF in een mast.
alles eigenbouw  PI4GN
op:
Jaap PA0T
Gerard PE1BBI   432
Peter   PA2V       10GHz
Frans PC5T
Sjaak   PA0JCA
Erik    PD1ET
Jaap PA0O
Nanko PA0V

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...