Skip to main content

5R8UI 6m first DX this year worked




recording with QSO PE5T

helaas 3B9FR niet gehoord  misschien weer te laat dat was een nieuwe geweest.
maar allang verbaasd om uberhaubt eens DX te horen op de ruisband...
tja 6m primetime = dinnertime   dat is een vaste regel..
5R8UI was langere tijd te werken simplex wel veel qsb

  

Nu de 70MHz preamp ESD protected   2x bliksem schade in maart na jaren 0-problemen.
hopelijk geen defecte preamp meer
info  http://www.ok2kkw.com/00003016/lna/lna_ochrana_en.htm
1N34 Ge diode  reverse -1.5V
ca 2pF @-1V      hier -1.5V U-gate

Beter nog zou een dual pindiode
BAR64-04W  of HSMP 3822 TRIG zijn maar die heb ik nu niet.
Of de NXP BAV99 dual SOT23   10 voor 1 Euro  Cp <= 1.5pF
Ik merk geen nadelig effect van de 1N34 of zelfs de BAT85 10pf  op 70 en 50 MHz
En een enkele diode gaat geleiden door te veel signaal en vormt dan een  gesloten contact.
Een harde kortsluiting is het niet maar de ingang wordt ook verstemd waardoor het signaal wordt begrensd
De ervaring van OK2KKW met deze beveiliging is goed.

4m en 6m  (U310  N6CA )



De BLF177 ook defect  nu een SD2931 ongeveer zelfde output.
De driver kan nu nog maximaal 3W sturing maken.
De XVTR stuurt 20-100mW naar een BLY88 die maakt maximaal 3W
De MRF238 trap erachter is uitgeschakeld , was nodig voor de BLX15 destijds.
Door zelf-oscillatie  kon de output 20W worden. vermoedelijk heeft me dat één SD2931 gekost.
Het geheel werkt nu stabieler.
Het uitgang circuit van de SD2931 is aangepast zodat η van 50% naar 60% is gestegen.
De BLF177 had zo ook beter gewerkt.
Volgende SS-PA  toch maar eens een  unbreakable type gebruiken.
Het is zo sneu werk een defecte LD-FET 




  

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...