Skip to main content

TJ3TS 50MHz decode WSPR?


 QSL manager of TJ3TS
PA3249  Harry noted me by mail
 this report was found
 2015-04-06 13:46  PA0O  50.294449  -23  0  JO33hg  1  TJ3TS  JJ53sv  5509  174 
like to believe this 
is not impossible  I was on 6m WSPR several days
but must be wrong band report

WSPR_ALL.txt  shows this log
tx-ing 50MHz   at 13:54  but there is a gap in the log between 13:44 and 13:54
that could mean no decodes in that time
At 13:46 I was not tx-ing according to this log

the WSPR_ALL.txt  file contains over 556.000  text records now
this file hidden in windows
"C:\Users\user\AppData\Local\VirtualStore\Program Files\WSPR\ALL_WSPR.TXT"
Not found it in the WSPR program path

150406 1342   2 -27 -1.1  28.126019  F1IEY JN25 27           0  5394    0
150406 1342   5 -26 -0.2  28.126052  DL6NL JO50 27           0     1    0
150406 1354                50.294479  Transmitting PA0O JO33 30          
150406 1358                28.126044  Transmitting PA0O JO33 30          
150406 1402   3 -30 -0.1  28.126052  DL6NL JO50 27           0  1292    0
150406 1402  18 -13 -0.4  28.126068  DK9JY JO30 37           0     1    0
150406 1402   4 -25 -1.1  28.126086  SA5SDR JO89 30         -2  1501    0
150406 1402   7 -24 -1.0  28.126096  ON7KO JO21 37           0   180    0
150406 1406                50.294479  Transmitting PA0O JO33 30          

Labels:

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het
3 comments
Read more