Skip to main content

ZD9XF VK9NT de kilo Watt is ook al gedevalueerd

ZD9XF   Zwak gehoord op 12 17 30 40m
Op 40m  dacht ik nog wel de beste kans te hebben goed te nemen  maar helaas de opzettelijke QRM werd te erg en Nigel ging QSY 30m daar had ik geen antenne meer.

Vanavond weer een dipool voor 30m opgehangen
prachtige avond nog warm en geen wind.
2x 7m+ nog wat  sloping dipool  de kat hielp me weer flink mee de draden vast te houden.

Past perfekt aan 1:1 werkte altijd goed hier een sloping dipool op 30m.

Hoorde VK9NT  op 10124   behoorlijk goed 559 zeer goed neembaar  niet erg druk
Maar geen responce  met 100W  en ook niet met de ACOM1000.
Na een poosje vissen met en zonder PA en zoeken naar de juiste QSX  heb ik het opgegeven met deze.


Daarna VK9AN  nog iets sterker 569(real) op 10.1137
PA weer uit als het zonder niet lukt dan hoeft het niet meer zo.
Waar zijn toch die DX-pedities met 100W met goed oren gebleven?
Mij horen ze nooit! het "DX-n" moet ik maar helemaal opgeven ik ben gewoon een SWL.
WSPR maar weer aangezet.




N1MM +     elke dag een update  dat gaat erg simpel  een klik slechts


Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...