Skip to main content

6M

gisteravond weer wat Caribian   zwakke signalen
Puerto Rico Guadeloupe  KP2 Virgin isl

 Santa Lucia  zowaar een nieuw DXCC (211) lukte net 53 maximaal
J69DS St Lucia flag St Lucia 
Frans van Santbrink
P.O. Box BB29
Babonneau
St Lucia


70 MHz Sterke ES  9+40 EI4DQ en anderen GI  GW  niets nieuw gehoord

Vanmorgen
5   nieuwe Japanse staions    zwak soms goed neembaar 539
20140703 0717  50083.6 CW   PA0O         519  JH0BBE          559                    
20140703 0718  50083.6 CW   PA0O         529  JQ2VVH          559 Kazu              
20140703 0732  50083.7 CW   PA0O         529  JH2UVL          559                    
20140703 0758  50081.1 CW   PA0O         559  JM1IGJ          559 Taka              
20140703 0801  50105.0 CW   PA0O         529  JR4OZR          559                    

 EX9T  Kirgizistan grenzend aan China   niet nieuw

 Propagatie  marginaal  vooral hier in Groningen lijkt het (...)
antenne  HF combie 4 ele 6m lijkt het wel goed te doen als ik zo vergelijk met anderen in de buurt
Sterk richting gevoellig  ruis toename bij aansluiten zonder externe preamp op de K3

Maar elke antenne heeft wel een beetje propagatie nodig.

Helaas deze 2  nieuwe DXCC   hier niet hoorbaar 
BV2DQ Taiwan
KL7KY  Alaska (gisteren vanuit SM4 gewerkt)

BA4SI af en toe 519  CQ  helaas geen reply
 de 1e keer  China  met werkbaar signaal
de laatste keer was 20 jaar? geleden super zwak
voorlopig  mijn laatste ochtend  QRV hier daarna zal het wel eens een keer echt losgaan.
China Taiwan Korea en Alaska uiteraard  blijft op de DX verlanglijst staan  moeilijk te werken op 6M

Het zijn  EME power stations die je marginaal hoort in Asie en ook nog in een pile dus moeilijk.
Ik krijg niet de indruk op een MAGIC BAND te zijn nog steeds niet.
Met een beetje Magic dan was het geen probleem geweest China Korea Taiwan Alaska.. denk ik dan



Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...