Skip to main content

HF + 6m 4ele Combi




HF dipool uitgebreid met  4ele 50MHz beam op een boom van 5m25. 
Dat is de originele boom van deze HF 4-band  4ele 10/15m   en dipool 20 en 40m  antenne. Ik gebruik nu alleen het dipool deel.
Nu dus een 4 ele skelleton feed / parasitair  gevoede  6m Yagi toegevoegd.
En het werkt mooi ook handig HF en 6 op 1 kabel. 
De  dipool voor 6m is nu op ca 20cm afstand van de HF straler.
10cm afstand  bij de eerste test gaf SGV >1:2  
Met grotere afstand gaat de 6M afstemming omlaag. 
Bij ca 20 cm  is de SGV  ca 1: 1:4 op 50.1MHz  op 50.3 is het 1:1.2
25cm afstand is mogelijk nog gunstiger.
De SGV van 40 20 15 en 10 worden niet beinvloed door de 6m elementen.
Met de SGV >1:2 was de ontvangst ook beter (tov de 2ele referentie)
Maar het is wel prettig om de aanpassing een beetje goed te hebben voor 50 OHm  liefst < 1: 1.5  

Het element maten heb ik van de DK7ZB site daar staat een 3 ele 10m antenne duoband 6m  
Echter de 9cm onderlinge afstand van de stralers moest ik aanpassen naar 20cm   ook is de 2e director op het eind van de boom geplaatst ipv op de  aangegeven 4m30. 
Helaas zijn de 6M condities zeer matig slechts een paar enkel hop ES 
Alleen in Zuid EU en Scandinavië word af en toe DX gemeld  ik hoorde vanavond ZD7VC niet, SM7FJE raporteerde 599   

Het balun aansluit doosje was trouwens gevuld met water..
De Balun bestaat uit  ca 50cm 6mm 50Ohm coax type gasgevuld polyetheen dielectricum low loss met er omheen geschoven ca 6 ferriet ringen ( Van Dijkenelektronica)
een eenvoudiger Balun kan ik niet bedenken waarom dat moeilijke toroide gewikkel als het zo ook kan?
Eerst maar water eruit laten lopen en geföhnt. De kabel lijkt niet aangetast.
Ik had af en toe al wat hoge SGV op 10m daarom dus.  Het aansluidoosje was dacht ik goed dicht met silicone kit .. dus niet
Kon het zo snel niet meer vervangen het was al middernacht toen alles klaar was om de mast weer omhoog te zetten..

De referentie  3bander erboven was bij de eerste vergelijkingen duidelijk slechter op het LX0SIX baken en diverse andere signalen.
Vermoedelijk een 5dB 

Gisternacht  met deze 4 ele W7GJ  via EME kunnen ontvangen -23dB  1 goede decode. 
W7GJ heb ik wel sterker gehoord met  de vorige antennes  de 7el LFA en de 7ele DK7ZB  -18 dacht ik maar misschien waren de EME condities niet zo goed. 

De 3band 6/4/2m  erbovenpikt  wel  2W op uit het veld op 50MHz 
Dat is nu een probleem voor 4M als ik deze antenne op de 4M transverter aansluit zou de preamp kunnen beschadigen 
De bedoeling is om er een 4/2m duoband in te zetten.








Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...