Skip to main content

recordings of T33A and K9W Wake Island.



This evening weak but workable T33A and first time heard K9W
40m rather weak possible not the best propagation tonight but my first time to copy them.
Just fixed my 30/40m inverted V
Used rotary dipole for 40m.  
Lot of QRI  including the crazy  QRX / "contester"  Dx-pedition jammer 

I have lost a bit my taste for joining DX-pedition pileup's with all the anti ham-spirit that comes with it.
But could not ignore these interesting DX-peditions because of this.
So I listened and tried just to ignore the deliberate QRI just as if it not existing.
Just wait until the jammer(s)  get tired and keep on listening for the right moment to call.
I  check my rig settings  to prevent unwanted simplex calling.
And If some ham makes that mistake  just do not join the up up concert causing more QRM then the HAM that send's simplex by mistake.  
When tuning I check the tune freq before and in between to prevent QRM-ing  not like some hams seem to do. Just start tuning on or very close to the DX-freq.  for a minute or so without checking.   As best as I can.
I think that's the only way to go not to receive a bully lid card..


http://www.qsl.net/pa0oos/recall/k9w_40.mp3

 earlier before dinner  T33A
http://www.qsl.net/pa0oos/recall/t33a_40.mp3
http://www.qsl.net/pa0oos/recall/t33a_30.mp3

Comments

aartw said…
Jaap mooi gewerkt.
Ik hoor ze op 40 ook wel maar erg zacht op een korte bev.
Op de rotary dipool teveel storing

Trouwens ook op de hogere banden veel storing/QRN. De zon is veel te actief.
pa0o said…
hier ook geen K9AY die moet k nog weer opzetten.
Ik hoorde K9W niet op 1826.5 vanavond.
Dat lukt alleen met een Beverage maar de schapen staan in de weg...
pa0o said…
Kon K9W vandaag op 12m werken met mijn zwabber draad dipool.. die hangt aan de 40/30 inverted-V
dus een 3-band dipool.

Hoorde K9W in RTTY op 40 maar te zwak voor QSO

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het