Skip to main content

CQWWCW a weekend at the radio ...





The big CQWW   already >5300 logs  received by organisation


Hunting  zones and multipliers   worked 39.
The missing one  34 not seen  very few Africans active.
The difficult zones 39 19 
This time I choose  for SO high power
Dipole and verticals and receive loop K9AY.  
Low bands  very poor the evening before the CQWWCW ( and the weeks before not better)10M had been very good last days until Friday  
500mW to ZL3PX  -16dB   3 days in a row ZL's decoded  then
CME  and propagation dropped.

Saturday early found 10m almost closed  very weak VK6DU  no change to work him 




Ja ik heb het wel een beetje bont gemaakt dit weekeinde in de CQWWCW  weer veel tijd voor de radio alle klussen weer uitgesteld..

Kon gelijk eens goed testen of N1MM met de US232 contestproof is  en de US232 is idd beter dan de Prolific chip types  geen problemen meer gehad.

Het was een zware belasting voor de logging PC   een enorm aantal clusterspots met alle reverse beacons een enorm aantal spots.
 De bandmap zat tjokvol paste niet meer op het scherm. Ook was het een een constant veranderende pool van calls vermoeiend voor de ogen ook blinkend nu zoals bij TR4W met een hoog aanbod van spots.  Blij dat N1MM weer heel goed werkte TR4W is zeker geen alternatief 
Niet eens zo'n snelle PC  een Notebook D420  "Core Duo" inside. 
Maar die kon het prima aan. Zou ook raar zijn dat dit niet zou gaan.

De condities tijdens de CQWWCW. 
Het zat er een beetje aan te komen de 10m was al weer te lang  goed dan kon niet goed blijven gaan. Er was vrijdag al een CME onderweg. Zaterdag ochtend was 10 haast dicht.
Redelijk herstel zondag op de valreep nog ZM4T op 10
Maar ja na een lange nacht iets te laat  voor de VK/ZL's op 10
De meeste QSO's op 80m dat werkte beter dan verwacht.
  


The US232 USB-serial  was a good buy no CAT errors appeared.
The US232 FTDI converter  must have better driver software. 
N1MM has been working flawless since the US232 USB-serial is in use 
Another good thing the 80m vertical here is far better then 
expected.
Good score on 80m and easy working the hard ones .
To my surprise could work JA and YE4W at 80 in poor band propagation.
YE4W very weak signal QSB  not hearing well with the high QRN  on the other end that is a hard one but I was real surprised he heard me. 
 I must be putting out a good signal that is sure.
 160m vertical is having problems in the high wind some short up in the mast in the dark.
 
W3LPL  and HK1NA worked on  6 bands and some more
overall propagation was better then expected.


Propagation recovered a bit   Sunday  TM4T on 10m weak could just be worked.
ZF1A high speed

zf1a_80.mp3

last week not in the CQWW  
5T0SP_160.mp3

5T0SP_160_1.mp3

 results
 section  high  SO assisted

    ARRL Section : DX
        Club/Team : CONTEST CLUB ZUIDWOLDE
         Software : N1MM Logger V12.11.1

        Band    QSOs    Pts  ZN    Cty
         1.8     266     335   14   47
         3.5     345     556   18   62
           7     249     490   29   66
          14     200     511   27   67
          21     107     262   32   61
          28     193     508   34   74
       Total    1360    2662  154  377


 
 


 
 

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het