Skip to main content

Very good ES day 10 June

70.20245 yo8ddp 4m.mp3


20120610 0748  70202,7 USB  PA0O          59  YO8DDP           59         kn36uf    
20120610 0809  70199,9 USB  PA0O          59  Y05TP            59         kn16ss    
20120610 0811  70207,7 USB  PA0O          59  YO3BL            59 kn32bk            
20120610 0818  70184,9 USB  PA0O          59  EA1FDI           59         in53tf    
20120610 0835  70211,9 USB  PA0O          59  YO4FYQ           59         kn44fd    
20120610 0842  70200,1 CW   PA0O         599  YO9IE           599         kn35aw    
20120610 0845  70214,8 USB  PA0O          59  YO8RAW           59         kn36uf    
20120610 0850  70201,4 USB  PA0O          59  EA6CA            59         jm19nl    
20120610 0852  70207,7 USB  PA0O          59  YO9HP            59 alex              
20120610 0857  70200,8 USB  PA0O          59  IF9/I2AND        59         jm67      
20120610 0916  70189,3 USB  PA0O          59  9A2SB            59         jn95gm    
20120610 1045  70192,0 USB  PA0O          59  CT1DIZ           59 Alex    im58kp    
20120610 1059  70199,7 USB  PA0O          51  EA8BPX           51                  
20120610 1106  70209,9 USB  PA0O          59  SV2RM            59         kn00pl    
20120610 1114  70204,8 USB  PA0O          55  S51DI            55         jn76      
20120610 1204  70215,0 USB  PA0O          59  9A6R             59         jn83      
20120610 1209  70215,0 USB  PA0O          59  9A2ZH            59 Franjo  jn73      
20120610 1236  70210,0 USB  PA0O          59  SV9GPV           59         km25ah    
20120610 1412  70195,9 USB  PA0O          59  I0JX             59         jn61      

EA8BPX   odx

today 3 new  4M  DXCC   

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...
4 comments
Read more