Skip to main content

Toch maar weer eens aan de knutsel voor 70MHz

Bezig met een kleine 3band VHF antenne DK7ZB   en  ombouwen van de 6m transverter naar 4m
 ca 100-150mW

De oude veel gemodificeerde 6m transverter  nu met een 42MHz VCXO
Kwam erachter dat de regel ingang pin1 van de  VX-4231 niet werkt maar de frequentie is behoorlijk in de buurt van 42MHz misschien scheelt het een paar honderd Hz zoals bij alle tot nog toe gemaakte x-tal oscillatoren het geval was... Helaas dus geen VCXO functie deze oscillator.
Ik herinner me nu dat de 22MHz x-tal oscillator  eerst mooi op frequentie was in 1986.. en toen viel het ding hard op de grond. Einde Xtal  het was een ex-tal geworden moest weer een nieuwe bestellen.. duurde en duurde . Maar het nieuwe x-tal moest met kunst en vliegwerk op de juiste frequentie worden getrokken..


Deze transverte heeft echt het minimum aantal actieve delen  3 transistoren 2 voor TX 1  RX  BFR34
 ontwerp is  vele jaren geleden door PE1CKK gepubliceerd
Toch komt er ruim 100mW uit.
Ik heb heel wat 6m landen ermee  gewerkt met een PA erachter natuurlijk.
Dat bewijst natuurlijk niet dat deze transverter goed is..
Ik vind het een slim ontwerp 2 Schottky dioden en een bandfilter (midden)  dat met dioden wordt omgeschakeld voor TX en RX gebruik.

Ik kan nog niet controleren of de ontvanger het doet geen  antenne nog
Maar daar wordt nu ook aangewerkt de 3 band Yagi/Una van DK7ZB
Het is nog wel even afwerken maar hopelijk ben ik dan snel ook op 4m actief
ooit wel x-band gemaakt  en Aurora signalen uit EI GM  gehoord op de IC706 die alleen ontvangt op 4m helaas geen TX mogelijk ivm hoge MF in de buurt van 70MHz.


Mantelstroom blokkering met een ringkern  4 windingen ca 200uH  zou toch moeten  werken
Een even grote blauwe ringkern geeft bij 4 wdg slechts 8uH    mogelijk is deze oranje kern niet geschikt voor VHF maar dan nog, Rf  gaat dan ook normaal door de  kabel 
Ik denk dat niemand verschil zal merken met of zonder de mantelstroom spoel.
Op lagere frequenties misschien wel een sterker effect? 

 

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...