Skip to main content

4 ele STEPPIR versus 7 ele LFA ??

Found 50MHz closed in the morning. I have the relative heavy 9m long 7ele LFA back at 22 M ag
Now I can make a direct compare

On LX0SIX  50.02165 :
The Steppir 4ele  included the extra 6meter director
At about 16Mm a.g. and 60m coax cable
And the 7 ele 9m boom at 22m ag 30m H2000

Yes  there is a clear audio difference in favour for the 7ele
But I would expect S units difference?
1 S-unit  only I think
Or the STEPPIR is super or this LFA  is doing not much
It is time to make a small good designed 6m/4m Una ..
And forget about this dragon...
This pictures made Saturday when I first could see the results of last night.




The JIDX  some JA's with good signals I guess only the big guns this time. Few weeks ago one could work JA in FM 10W..

PABEKER-CW  33 QSO  toen maar aan de koffie en gestopt  er kwam niemand meer retour  op 80/40
 



Comments

Tjeerd, PA3GNZ said…
Bedankt voor het QSO op 80M tijdens de PA beker CW. Ik heb ongeveer het dubbele aantal qso's gemaakt, QRP.

73, Tjeerd
PA3GNZ
PE4BAS, Bas said…
Hallo Jaap, wel relatief weinig QSO's in de PA-beker. Waren de condities zo slecht? Absorbsie? Weinig verschil tussen de steppIR en de LFA, zou je niet verwachten. 1,5-2 S-punten verschil zou het toch wel moeten maken. Weet niet wat de versterking is van beide antenne's? Je zou het ongeveer uit kunnen rekenen. DOe je morgen ook mee in het SSB gedeelte van de PA-beker? 73, Bas
Tjeerd, PA3GNZ said…
Jaap,

Het is mij bekend dat Gerard meer qso's heeft. Als ik maar in de top 3 zit. ;-)

73, Tjeerd

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het