Skip to main content

Netwerkte het netwerk nog nu werkt het net niet

Why do networks always resist till the very last bit to work properly ?


De raadselachtige wereld van het netwerk.


Gisteren werkte N1MM  met 2 users prima
vanavond zelfde configuratie
netwerk naam lijsten identiek  zelfde prog versie  zelfde contest hoewel gisteren met verschillende "contest"werkte het toch  met waarschuwing


nu willlen de logs niet synchroon.


  de K3  als master  192.168.2.101
de IC706  user 1  ip 192.168.2.104


beiden kunnen elkaar pingen  zelfde router / subnet
maar: connection failed


tja misschien morgen beter


je weet het maar nooit met die netwerken  soms hebben ze er gewoon geen zin in.



achteraf 
Restart N1MM van user1 toen werkte het weer ok..
Afterwards restarting N1MM at user2  did fix the problem.




propagation WSPR
160 en 80m  de laatste dagen zo dood als een deur  amper 2000km haalbaar
28MHz vandaag iets hersteld
 VK4ABW/8 Darwin  vele decodes en V53ARC
gisteren CX2ABN tot laat in de avond vele decodes


STEPPIR, de mast staat nu wat lager op ca 12m vlak boven een boom op storm stand.
Vanavond op 18MHz/17m   De voor/achter verhouding op deze band is enorm.
4S7NE  en  9Y4LAS  S8 signaal ging haast helemaal onder in de ruis op reverse.
Extreem F/B ook op 20m c.a. 20dBvoor/achter.
Af en toe moest ik de elementen even resetten.   Het besturingskastje merkt niet dat de stuurkabel eruit is en gaat vrolijk door met afstemmen..
Maar hij werkt als een speer.



KD1KT 18.149MHz  F/B switching reverse and back 3el STEPPIR  S9+15  down to S5!

Labels:

Comments

PE4BAS, Bas said…
Leuk filmpje Jaap. Wat een verschil dat 180 gr omzetten. 73, Bas
September 17, 2011 at 3:27 PM
Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its n...
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjuste...
11 comments
Read more

TS790 cat interface

A CAT interface  for the old TS790 144/432/1292 tranceiver to work with N1MM  including the internal CW keyer DTR and "PTT" RTS and WSJT MSHV with "PTT" control Using the 3€ FTDI USB serial interface picture bottom page first i bought the Kenwood USB serial interface cable that cable has the TS790 special 6 pin DIN plug this interface works well ...as long as you cut the 4-5  wire bridge on the ACC din.. with the wire bridge it did go offline after 30 seconds or so  Kenwood interface cable with CH330 eBay 15€    This type Kenwood interface cable uses a tiny 6 pin USB CH330 chip  The driver is CH340 known for Arduino it workes in W7/10 64  It has only TX RX Usart function no DTR RTS available  The TS790 settings are 4800b 8bit data 2 stop  default  N1MM does not list the TS790 it has the TS890  but that one does not support modes the TS2000 does support freq and modes and let you switch 2/70/23 it seem...
4 comments
Read more